Another P38 (EAS ISSUES)

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
I think my P38 is cursedo_O went to start it this morning and no start , winds over, no warnings on the dash, no smoke not even an attempt to fire ,Im thinking that the leaking injector has let the fuel drain back and can't hear the tank pump run so that's probably buggered too :mad: the list of jobs is progressively getting bigger:eek:
 
Right chaps I got to have a look at my P38 last night and found it cranks but no fuel plugged my crap on scanner in and I have fault code (27 anti theft device ) I'm assuming that the key has lost sync ? But I don't get an engine immobilized message on the dash ? And the led doesn't flash on the top of the dash either after it's been unlocked with the key ? It also has 12v on the solenoid on the back of the FIP with the ignition on ? Any of you lot come across this before?
 
Bern768 said:
Right chaps I got to have a look at my P38 last night and found it cranks but no fuel plugged my crap on scanner in and I have fault code (27 anti theft device ) I'm assuming that the key has lost sync ? But I don't get an engine immobilized message on the dash ? And the led doesn't flash on the top of the dash either after it's been unlocked with the key ? It also has 12v on the solenoid on the back of the FIP with the ignition on ? Any of you lot come across this before?
Click to expand...
It needs the car to be unlocked with the FOB to mobilise the engine and let it start unless EKA and immobiliser are turned off in the BECM which can be done with Nanocom.
 
Datatek said:
It needs the car to be unlocked with the FOB to mobilise the engine and let it start unless EKA and immobiliser are turned off in the BECM which can be done with Nanocom.
Click to expand...
Ok seems odd that I have been using just the key for weeks and has no messages on the dash etc not even sure they key fob works tbh I do have the eka code for it i think tho
 
Bern768 said:
Right chaps I got to have a look at my P38 last night and found it cranks but no fuel plugged my crap on scanner in and I have fault code (27 anti theft device ) I'm assuming that the key has lost sync ? But I don't get an engine immobilized message on the dash ? And the led doesn't flash on the top of the dash either after it's been unlocked with the key ? It also has 12v on the solenoid on the back of the FIP with the ignition on ? Any of you lot come across this before?
Click to expand...

Could be loss of sync between EMS and BECM.
 
Well the key does not want to sync with it and the eka code won't enter no chirp from the alarm and just operates the locks and does no more , comes up with the same fault code 27 anti theft device , safe to say it's a brick :( actually I think a brick would be more useful
 
Bern768 said:
Well the key does not want to sync with it and the eka code won't enter no chirp from the alarm and just operates the locks and does no more , comes up with the same fault code 27 anti theft device , safe to say it's a brick :( actually I think a brick would be more useful
Click to expand...
Is yours a manual? The sidelight warning light should illuminate each time the key is turned when entering the eka code if it does then the input is being sent to the BECM.are you entering the eka correctly?I believe @DanClarke did a guide.
 
You must log in or register to reply here.

Similar threads

Flossie
P38A Eas issues
2
Replies
22
Views
1K
Datatek
Datatek
feyniriel
P38 EAS problems
Replies
18
Views
1K
pwood999
pwood999
J
P38A p38 EAS - immediate drop of pressure
Replies
11
Views
627
Mark Piercy
Mark Piercy
pwood999
P38A Asthmatic EAS Exhaust Port !!
Replies
6
Views
649
pwood999
pwood999
ar1g3
P38A Which EAS repair kit to get?
Replies
18
Views
1K
Grrrrrr
Grrrrrr
Back
Top