P38A 4.6 hse

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Trojan69skin

Trojan69skin

Member
Posts
11
Location
Langport Somerset
Hi all, anyone out there near langport Somerset, at my wits end with this rangie, dead door no window or mirror, got eka lockout, fob flashing ok, won’t accept eka, tried ignition sink, cleaned plugs in door jam, all was well until I got a flat battery, central locking not working, willing to pay if anyone can sort it, Dave
 
Trojan69skin said:
Hi all, anyone out there near langport Somerset, at my wits end with this rangie, dead door no window or mirror, got eka lockout, fob flashing ok, won’t accept eka, tried ignition sink, cleaned plugs in door jam, all was well until I got a flat battery, central locking not working, willing to pay if anyone can sort it, Dave
Click to expand...
Sounds like you have micro switch problems in the drivers door lock or the block connectors behind the A post kick panels are corroded, best cut them out solder and heat shrink the wires. Hopefully you can open the drivers door,there is a switch test write up by @martyuk ,don't know wether its in the technical archive, if not do a search.
 
Are you absolutely 100% positive and without a doubt sure that you entered the EKA code totally correctly? I dont mean just the correct code
 
If nothing works on the door, you might have door outstation problems. The pin connections look the same in RAVE, so maybe swap the left & Right ones over to see if the window & mirror faults move across. If the other one works, and microswitches are good, then you might be able to enter the EKA successfully.

If you have a simply continuity checker, then verify all of the connections from Latch to Outstation, and Outstation to BECM are good.
 
Last edited:
This diagram should be all the connections you need to check.


upload_2021-1-13_17-19-0.png
 
Hi all, I heard that it’s possible to send my becm, key fob and door latch off and have it reset, if it is possible anyone know anyone who can do it? Much appreciate all your help
 
Before you send anything away, it better to check the door latch, outstation & wiring continuity. If you don't have one, buy a cheap multimeter from your local Screwfix, B&Q, etc. e.g. https://www.screwfix.com/p/lap-mas830b-digital-multimeter-600v/75337

Then check continuity between the BECM & Door Outstation, plus follow the latch tests posted above. From your description that window, mirror & locking all don't work, it sounds more like BECM to Door communications, or 12V & Ground issue to the door. Window should work even if the latch is broken.

After that you will have a better idea what needs fixing. Once you get the communications & latch working, then you can try the EKA. The BECM only needs reset if its' memory has been corrupted.
 
The door latch is a plug and play, no programming or reset possible.
It is just metal latches and switches.
Callrova can go over you becm but without good reason it's money out the window but not in your case :p
 
Hi all, spent about half hour on the car today cos my patience is getting very thin on this motor, I’ve discovered that I’m only getting power to the large plug on the outstation, the right one if you’re looking from left to right, any thoughts on what’s going on all you rangie nuts out there? Much appreciated all
 
The BECM outputs vary. Some are 12V when active, but others are pull down to 0V. BECM Sys Info Doc has the details. My copy is a bit blurry, but the details are in there.
 

Attachments

  • BECM SID CONSOL.pdf
    2.2 MB · Views: 249
You must log in or register to reply here.

Similar threads

M
Central lock
2 3 4
Replies
77
Views
3K
kermit_rr
kermit_rr
Khemitude
P38A Becm/alarm throwing a funny
Replies
2
Views
1K
Grrrrrr
Grrrrrr
M
2.5 ton paperweight??
17 18 19
Replies
373
Views
24K
Mark Piercy
Mark Piercy
C
Central locking/alarm problems
Replies
8
Views
1K
Chris53
C
Muddy viking
Disco 2 Very strange...
Replies
4
Views
1K
Muddy viking
Muddy viking
Back
Top