What have you done to your Landie today.

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
nick2303 said:
spent all day messin wiv leakin swivel ball seal....

losened every nut but 1... the top one of the ones that hold the plate that holds the seal in...

snapped my 8mm spanner,,, ive hit it, soaked it in wd40, hit it some more, bought a set of proffesional spanners, which rounded it... filed it down to 7mm, still rounded it, tried bashin a 7mm socket on to it and socket failed,

gonna have to take off the whole hub i guess.. so i can get more violent.. aaargh,,,

lookin at swivel ball its a bit pitted so i'm gonna change that at same time...

buster makes it look easy but i bet it aint gonna be...
Click to expand...
did you use a 6 point socket instead of a 12 point?
 
Managed to undo the rest of the bolts holding the tub on and disconnected the wiring to the tub and also the fuel hoses. Removed the tub and quite happy with the condition of the chassis. I wire brushed the flaking paint and mud off and looks like it only needs a tank outrigger. This is its 2nd resto' as the rear 1/4 chassis and another outrigger has been done before and are still good. Brake pipes look okay but I will probably completely renew them. Here are some photos of the chassis before and after the rub down. I also drained the fuel tank.
 

Attachments

  • Randoms 347.jpg
    Randoms 347.jpg
    249 KB · Views: 164
  • Randoms 348.jpg
    Randoms 348.jpg
    246.5 KB · Views: 153
  • Randoms 349.jpg
    Randoms 349.jpg
    261.7 KB · Views: 188
  • Randoms 350.jpg
    Randoms 350.jpg
    230.1 KB · Views: 171
  • Randoms 351.jpg
    Randoms 351.jpg
    252.5 KB · Views: 146
  • Randoms 352.jpg
    Randoms 352.jpg
    255.7 KB · Views: 168
Fitted a new steering wheel with snap off boss kit! i need to sell my original steering wheel now but not sure how to access the selling area?
 
Last edited:
nick2303 said:
couldnt find my 12 point socket set... but used 12 point ring spanner... and not much access for socket as suspension spring in the way...

but bolt head pretty much crumbled as it was so rusty..
Click to expand...


when you use 12 point wrenches or sockets on old and rusty bolts/nuts you will round the heads. Use 6 point tools and that won't happen
 
well as cant do the seal and the swivel ball pitted too... gonna take the lot off and rebuild.. or buy the full hub etc from scrappers and fit that if i can get for right price..

so today i replaced the rear body mounts.. i hate welding upside down!! i'm burnt all over, set myself on fire a few times... gotta buy a garage and a car lift!!
 
finally got around to fitting the air bypass pipe around the MAF sensor (suppose to fool the ECU into extra air flow)

IMG-20110906-00013.jpg


got the hard door fitted after having it sprayed

IMG-20110905-00009.jpg

put a landyzone sticker on it as well :D
 
Cleaned up and removed rust form sills then painted The buggers with zinc primer statin black top coat and under seal spraed a rust injurie in them after it dryed a dose of waxoil so it should last a week.
 
Apart from fun dragging a bit of timber round the woods (I love teaching :)) swopped over my spare wheel carrier and fitted my razor edge bonnet................looks so much better than the deluxe
 
You must log in or register to reply here.

Similar threads

B
defender 2.4 puma reverse light switch
Replies
4
Views
469
BEASTIE 90
B
Padda.116
300tdi disco 1, new head gasket oil leak!!
Replies
10
Views
567
Padda.116
Padda.116
Knappster
Shot-blasting steel wheels
Replies
9
Views
826
Knappster
Knappster
I
Re-coding of ABS Module after repacement
Replies
10
Views
908
invisible999
I
C
Freelander 1 crank no start
Replies
1
Views
1K
niccage
N
Back
Top