ratty
I'm not special I'm limited edition
- Posts
- 34,277
Changed the mirrors (or what was left of them) with the help of the lz resident porn addict. We also fitted replacement number plates and bent the cb aerial back into shape.
What have you done to your Landie today.
- Thread starter madfrank
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Langers
Well-Known Member
- Posts
- 3,162
- Location
- Kent or Shropshire
Just replaced the entire fuel tank to lift pump pipe (including new compression fitting at tank end, and new union at pump end), in the hope of eradicating this fuel starvation/air in fuel problem, but to no avail 
Have now replaced fuel sender unit, tank to pump pipe, lift pump itself, pump to filter pipe, fuel filter itself and I still, STILL have this problem
Just about ready to set fire to the ****er
Have now replaced fuel sender unit, tank to pump pipe, lift pump itself, pump to filter pipe, fuel filter itself and I still, STILL have this problem
Just about ready to set fire to the ****er
Yogi Bear
New Member
- Posts
- 174
- Location
- Chesterfield
Just replaced the entire fuel tank to lift pump pipe (including new compression fitting at tank end, and new union at pump end), in the hope of eradicating this fuel starvation/air in fuel problem, but to no avail
Have now replaced fuel sender unit, tank to pump pipe, lift pump itself, pump to filter pipe, fuel filter itself and I still, STILL have this problem
Just about ready to set fire to the ****er
Join the club fella, in the same boat as you I think.
6 months of work and it does this to me on MOT day, have a vic check coming too and even tho I told them it wasn't on the road they still say I have to take it to them.
Best give it another kick to be sure on my way out.
Headtester
Active Member
- Posts
- 581
- Location
- Ruislip
Took it for its MOT and passed, got an advisory on missing bump stops - dunno what happened to them?
defender11069
AKA Mr cool...
- Posts
- 8,616
- Location
- up sh*t creek with out a paddle
nick2303
Well-Known Member
- Posts
- 4,255
- Location
- Leeds (not by choice)
took swivel/ hub and disc assembly off a scrapper and swopped all the bits as my swivel and seal was fubar....
£55... £200 cheaper than garage quoted me for the job..
cheers buster for another superb how to guide...
£55... £200 cheaper than garage quoted me for the job..
cheers buster for another superb how to guide...
PickUp90
New Member
- Posts
- 358
- Location
- Oxfordshire
Waited. ... been in the paint shop for a week, another week to wait :frown:
reads90
New Member
- Posts
- 87
- Location
- Brisbane , Australia
200tdi ayre
Well-Known Member
- Posts
- 5,832
- Location
- Ashbourne (sometimes)
made a light bar and wired the lights up, like making instead of buying
nick2303
Well-Known Member
- Posts
- 4,255
- Location
- Leeds (not by choice)
lost my chuffin n/s rear bumper corner!
where the hell did that go???
must of fell off on my way home this mornin...
got enough to do for the mot, now i gotta find another one of them!
where the hell did that go???
must of fell off on my way home this mornin...
got enough to do for the mot, now i gotta find another one of them!
joe1972
Well-Known Member
- Posts
- 1,595
- Location
- Manchester
I think I have a spare bumper corner for a RRC which is useless to me (daily driver got those GF brookland bumpers n bobtail doesnt use them)....can't remember which side, but think they are differentprofile??
nick2303
Well-Known Member
- Posts
- 4,255
- Location
- Leeds (not by choice)
I think I have a spare bumper corner for a RRC which is useless to me (daily driver got those GF brookland bumpers n bobtail doesnt use them)....can't remember which side, but think they are differentprofile??
cheers joe.. but no doubt it will be different than a disco one...
joe1972
Well-Known Member
- Posts
- 1,595
- Location
- Manchester
oh well...the thought was there.
If ya need any ball jointslet me know...
I got a big box load bought as a job lot, left and right hand threads. think they are the same
landrover11019
Active Member
- Posts
- 852
- Location
- essex
Retightened my head and checked the tappets, all good.
Karlos28
Well-Known Member
- Posts
- 1,894
- Location
- Derbyshire
bodged an alternator belt out of an air hostesses tights..... ****ing ****part one destroyed itself!
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
Fitted me CP door panel. Need to get some decent SS CS socket haed screws as the bolts look ****.
matthew2riches
New Member
- Posts
- 3,025
- Location
- Suffolk
Stripped rest of crap off chassis ready for shotblasting tomorrow afternoon
crashbox
Well-Known Member
- Posts
- 12,347
- Location
- In the UK, thankfully.
Removed the aluminium chequer footplates and gearbox tunnel cover. Found holes in front nearside bulkhead outrigger and petrol tank outriggers and on the chassis forward of f/o/s bulkhead outrigger. Still quite happy as it could be worse. Next job removing front wings...aaaahhhhhhhhh.
