What have you done to your Landie today.

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
greenlaner said:
............fink I mite be in the doghouse
Click to expand...

Squeaky_chicken_toy_promotion_gifts.jpg


:D
 
Hi,

I've gone and bought another disco! It a 95 m reg. done 130,000 with 2 owners and (i can not quite beleive it) full land rover service history. I'm off to Austria in Dec. Going to drive it down. I'm in the middle of doing the following to it,

2" inch lift kit, shocks and hd springs,
winch and bumper
larger profile tyres
straight though exhaust
snorkel
replacing inner wings. rusted!
roof rack
rock sliders
and few other bits.

Looking forward to next week when its done.
 
tighted n/s wheel bearing after spending 46 quid to get the 52mm socket.. long story you dont wanna know..

and found that all that effort might not of been needed... as the o/s track rod end has play in it! tw@t!

gonna get one of them tomorrow and start again...

replaced rear brake pads...

just got swivel ball seal to do next and loads of weldin for mot at end of month...
 
Stripped handbrake yesterday to see why the ratchet was not holding (Ser III). The end of the pawl was flat instead of pointy, so tried to file it, but too hard (ie hardened, not difficult). Today bought a new one (£2.50 + vat!) and rebuilt it all again. What would that have cost for almost any other vehicle? Took me 4 hours though, but I was very thorough!! Now it stays stopped. :)
 
repaired a broken leccy window wire in drivers door yesterday soldered the new wire in (save me doing it again if i'd used crimp conectors ) worked fine all afternoon yesterday, then this morning the bloody switch is playing up :mad:
picked up the hard door for the ifor williams after spraying looks the bollocks will get a picy in the day light tomorrow
 
Took my J plater disco 200dti to local MOT station yesterday, after being sorned since all my work last summer!..:cool:..like a dad @ maternity, sitting, waiting, patiently for a result..:eek:.oh dear, the tester has just asked his mates to come down the inspection pit to "have a look at all this welding"......shouted from the pit "who did all this?"...:eek:...errr, it was me mate!....why?....."never seen welding as good as ALL this for ages, and you said you did it?"...err yes mate!.....all the mekiniks then came out from under smiling - good or bad thing I thought!....:doh:.....yeh, it`s passed mate, nice job you done, you even painted insides of the wheels!!, just one very small advisory though...(here we go i thought)...offside trackrod end very slight play, the rest, brillient...WHOOPPPPEEEEEEE I thought deep inside...just like a very proud dad, out I came holding my babies birthrite VOSA form.....It took 3 months of my time last summer, getting burnt, covered in ****e, backache, neck ache, arm ache, from all the fabrication, welding, cutting, painting, but, was I proud of my baby...
Now, my making of my kids were, If i can remember that far back, all over in a few minuets or so, or so my wife tells me.:blabla:...At 63 years of age, I`m a new "father"....ha....ha...ha...AGAIN....
Landies, dont you just luv `em eh....
 
Hi all, pretty new to the forum and Land Rovers, bought a 2000 Disco TD5 a week ago yesterday and have only really done some tinkering so far.

Cruise control fitted (in prep for a trip to the Lakes we did last weekend)
Cig Lighter rewired
Door trim refitted correctly
Panic over missing rocker cover bolt (sheared) when checking the EGR mod that's on.

Planned to do:
Full service - only got receipts for parts and oil etc since 2007 so not sure when it was last done.
Chassis cleanup & Wax Oil.
Sunroof drain pipe cleanout/reattach.
Anything else I find :D
 
easye1 said:
Took my J plater disco 200dti to local MOT station yesterday, after being sorned since all my work last summer!..:cool:..like a dad @ maternity, sitting, waiting, patiently for a result..:eek:.oh dear, the tester has just asked his mates to come down the inspection pit to "have a look at all this welding"......shouted from the pit "who did all this?"...:eek:...errr, it was me mate!....why?....."never seen welding as good as ALL this for ages, and you said you did it?"...err yes mate!.....all the mekiniks then came out from under smiling - good or bad thing I thought!....:doh:.....yeh, it`s passed mate, nice job you done, you even painted insides of the wheels!!, just one very small advisory though...(here we go i thought)...offside trackrod end very slight play, the rest, brillient...WHOOPPPPEEEEEEE I thought deep inside...just like a very proud dad, out I came holding my babies birthrite VOSA form.....It took 3 months of my time last summer, getting burnt, covered in ****e, backache, neck ache, arm ache, from all the fabrication, welding, cutting, painting, but, was I proud of my baby...
Now, my making of my kids were, If i can remember that far back, all over in a few minuets or so, or so my wife tells me.:blabla:...At 63 years of age, I`m a new "father"....ha....ha...ha...AGAIN....
Landies, dont you just luv `em eh....
Click to expand...


Good goin coffin dodger :D:D
 
spent all day messin wiv leakin swivel ball seal....

losened every nut but 1... the top one of the ones that hold the plate that holds the seal in...

snapped my 8mm spanner,,, ive hit it, soaked it in wd40, hit it some more, bought a set of proffesional spanners, which rounded it... filed it down to 7mm, still rounded it, tried bashin a 7mm socket on to it and socket failed,

gonna have to take off the whole hub i guess.. so i can get more violent.. aaargh,,,

lookin at swivel ball its a bit pitted so i'm gonna change that at same time...

buster makes it look easy but i bet it aint gonna be...
 
Spent a couple of theraputic hours grinding off and undoing the bolts that hold the front of the Ser3 tub to the seat base. Stopped for today, only a couple more to do then lift the tub off to let me see the state of the chassis. photos will follow when the tub comes off.
 
not mine but my dads, spent a few hours figuring out what was wrong with it and writing a list of parts that need to be replaced. so next week ill be fitting a new track rod, thermostat and making a switch for the front fans so he can turn them on and off when needed, seeing as they dont work at all currently...
 
You must log in or register to reply here.

Similar threads

B
defender 2.4 puma reverse light switch
Replies
4
Views
469
BEASTIE 90
B
Padda.116
300tdi disco 1, new head gasket oil leak!!
Replies
10
Views
567
Padda.116
Padda.116
Knappster
Shot-blasting steel wheels
Replies
9
Views
826
Knappster
Knappster
I
Re-coding of ABS Module after repacement
Replies
10
Views
908
invisible999
I
C
Freelander 1 crank no start
Replies
1
Views
1K
niccage
N
Back
Top