- Posts
- 22,905
- Location
- In the next Glen
Pulled the autobox out my D1 as im going to convert it to a manual...
Other what have u done on ur disco today
- Thread starter gstuart
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Shimsteriom
Master Procrastinator
- Posts
- 41,905
- Location
- Over Here
Back from doing two laps of the TT course (plus a bit to my house, so 80ish miles)
Once with the MAF disconnected and then again with the brand new LR MAF connected.
What was the difference? With the MAF connected, the engine seemed to have a little more torque at the lower revs and felt smother at the higher revs, but other than that, there was no real difference.
In fact, the difference was so little, I don't think that unless you've got previous experience of a TD5 engine with working MAF connected that you would ever be able to tell that something was wrong!
If anyone else would like to repeat a similar experiment, I'd be interested to know what your findings are.
Once with the MAF disconnected and then again with the brand new LR MAF connected.
What was the difference? With the MAF connected, the engine seemed to have a little more torque at the lower revs and felt smother at the higher revs, but other than that, there was no real difference.
In fact, the difference was so little, I don't think that unless you've got previous experience of a TD5 engine with working MAF connected that you would ever be able to tell that something was wrong!
If anyone else would like to repeat a similar experiment, I'd be interested to know what your findings are.
neilly
Well-Known Member
- Posts
- 20,000
- Location
- Oxfordshireness
Back from doing two laps of the TT course (plus a bit to my house, so 80ish miles)
Once with the MAF disconnected and then again with the brand new LR MAF connected.
What was the difference? With the MAF connected, the engine seemed to have a little more torque at the lower revs and felt smother at the higher revs, but other than that, there was no real difference.
In fact, the difference was so little, I don't think that unless you've got previous experience of a TD5 engine with working MAF connected that you would ever be able to tell that something was wrong!
If anyone else would like to repeat a similar experiment, I'd be interested to know what your findings are.
You forgot the lap with the VDO generic MAF fitted!!...................Out you go again.
Cheers
Shimsteriom
Master Procrastinator
- Posts
- 41,905
- Location
- Over Here
Not a chance, I've already proved to myself that the MAF seems to be pointless.You forgot the lap with the VDO generic MAF fitted!!...................Out you go again.
- Posts
- 225
- Location
- Blyth Northumberland
Its been a while since I have posted but not much happened with V8
I had problems getting the old Lambda sensor out of the exhaust so decided to take Y piece down pipe off, well bit of a chew on and it came off, 1 snapped stud in manifold, tried getting it out - no luck, manifold is off to extract snapped bolt - that's where i am at.
I had problems getting the old Lambda sensor out of the exhaust so decided to take Y piece down pipe off, well bit of a chew on and it came off, 1 snapped stud in manifold, tried getting it out - no luck, manifold is off to extract snapped bolt - that's where i am at.
beanwood
Active Member
- Posts
- 109
- Location
- North of Bristol
I replaced my drivers door locking mechanism!! .
I now have a car that locks on the button, and both front doors unlock on the button!!
OK. so the rear two doors are both locking, but not unlocking, but hey - that'll go on the list....
Oh, and a bit more cleaning...
. I now have a car that locks on the button, and both front doors unlock on the button!!
OK. so the rear two doors are both locking, but not unlocking, but hey - that'll go on the list....
Oh, and a bit more cleaning...
Shimsteriom
Master Procrastinator
- Posts
- 41,905
- Location
- Over Here
Hoovered the carpets only to discover that the front passenger carpet is quite moist.
I've been using the AC all the time recently, so I'm going to check the drain plugs tomorrow.
I've been using the AC all the time recently, so I'm going to check the drain plugs tomorrow.
Shimsteriom
Master Procrastinator
- Posts
- 41,905
- Location
- Over Here
It's not the AC drains... realised how easy it was to check them so just been out now. I'll check the roof gully tomorrow...
I don't think it's the sunroofs as they've been sealed for a while now, and when they did leak, the water would come out of the B-pillars straight down my neck!
I don't think it's the sunroofs as they've been sealed for a while now, and when they did leak, the water would come out of the B-pillars straight down my neck!
Let's hope it's not heater matrix
brianconwy
Well-Known Member
- Posts
- 1,112
- Location
- conwy, north wales
I notice in ours there is some water around the bonnet release lever. Haven't a clue where it might be coming from.
- Posts
- 83,282
- Location
- Embasinga stocæ
Outside?
Had that on a Merc and it turned out the windscreen wasn't sealed down by Merc properly
Scuttle panel drains?
brianconwy
Well-Known Member
- Posts
- 1,112
- Location
- conwy, north wales
It Is on the to do list after the clutch and bigger leak from roof area.Had that on a Merc and it turned out the windscreen wasn't sealed down by Merc properly
Shimsteriom
Master Procrastinator
- Posts
- 41,905
- Location
- Over Here
Took SWMBO's D1 for its MOT - passed, no advisories
Happy days , is always a nerve racking experience
I had the Worst luck when I had my last mot , because the back door lock failed shut whilst on the mot ramp , dealer wanted to rip the door card off and give me a bill for around £500 , done it myself for £60 quid, took it back for a free retest , passed, no advisories
brianconwy
Well-Known Member
- Posts
- 1,112
- Location
- conwy, north wales
We have a local MOT testing station that does nothing else, so when anything fails they aren't looking to do the work.
£500 !
- One thing I noticed with our A-Plan policy was that if "it" fails the MOT, then Ins cover reduces to Act insurance - which means if you have an accident, you're probably going to be seriously up sh*t creek .... just something to be aware of....+1 - and always go as scruffy as you can manage on the day, with a nice clean car
- I.E. scruffy means you've got no money , but you look after the car, so ....brianconwy
Well-Known Member
- Posts
- 1,112
- Location
- conwy, north wales
Preparing for changing the clutch. Have removed cross-members, propshafts, front exhaust, starter motor, viscous fan, center console and gear lever. Have disconnected crank sensor, clutch slave cylinder, reverse light switch and hand brake cable. Drained transfer box and gearbox oils. I need to remove plate by gear lever so I can use my engine hoist and move middle section of exhaust aside.
I am feeling a little daunted and wondering should I have just taken it to a garage.
I am working tomorrow and will continue on Friday.
Does removing the small plate by the gear lever provide enough space for hoisting?
I am feeling a little daunted and wondering should I have just taken it to a garage.
I am working tomorrow and will continue on Friday.
Does removing the small plate by the gear lever provide enough space for hoisting?
