CarlosVanDango
Active Member
- Posts
- 197
- Location
- Rotherham
thats not a straight 6 is it????
Stood for 20 yrs - 109 series 3 resto thread.
- Thread starter CarlosVanDango
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
Aye, it is.
honolulujoe
Well-Known Member
- Posts
- 6,137
- Location
- richmond surrey
going back to near the start of the thread and that low spare bracket on the door, one reason might be to carry bigger tyres, I have 7.50's on mine apart from on the back door, even with a standard small tyre the door handle and lock are a bit difficult to get at, if I put a 7.50 on there I wouldn't be able to access the lock or the handle
pocketrocket
Active Member
- Posts
- 658
- Location
- sheffield
Just caught up with the progress, the wellas look well, you used the tyres from the old rims? And have you got her running yet?
ciderman
Active Member
- Posts
- 770
- Location
- sunny worcestershire
Scrape a six cylinder?
What do you mean?
What do you mean?
CarlosVanDango
Active Member
- Posts
- 197
- Location
- Rotherham
bit steady at the moment tbh
i'll get back onto it soon tho - i'm aiming to have it roadworthy for the end of this summer
honolulujoe
Well-Known Member
- Posts
- 6,137
- Location
- richmond surrey
probably a typo should say scrap?
CarlosVanDango
Active Member
- Posts
- 197
- Location
- Rotherham
CarlosVanDango
Active Member
- Posts
- 197
- Location
- Rotherham
no it doesnt run yet:frown: but luckly i can sleep ok
pocketrocket
Active Member
- Posts
- 658
- Location
- sheffield
no it doesnt run yet:frown: but luckly i can sleep ok
So whats the latest progress luke?
CarlosVanDango
Active Member
- Posts
- 197
- Location
- Rotherham
well i convened a project planning meeting with all those involved drew up a critical path analysis schedule, realised we was behind target schedule - moved the completion date so progress looked good - wrote a report praising all those involved in keeping the project on schedule
.............sorry thought i was back at TI for a sec there
actually done sod all but my gate is nearly finished
pocketrocket
Active Member
- Posts
- 658
- Location
- sheffield
well i convened a project planning meeting with all those involved drew up a critical path analysis schedule, realised we was behind target schedule - moved the completion date so progress looked good - wrote a report praising all those involved in keeping the project on schedule
.............sorry thought i was back at TI for a sec there
actually done sod all but my gate is nearly finished
Wasnt realy for my benefit as i already know what you`ve been up to, just thought others mite like to know hahaha
CarlosVanDango
Active Member
- Posts
- 197
- Location
- Rotherham
got the GB springs parabolics fitted on the back - it sits nice and high (pic attached) which i'm pleased about - the problem is it bottoms out on the shockers - whats the method of sorting this and getting more articulation will i need to fit longer shockers and raise the top mounts???? i'll have a research on here about that but any tips?? best shocks to buy???
got the petrol to the carb and it fired up almost 1st go (too quick for a video pete) but fuel leaked out of the bottom of the carb - i thought it was a drain plug so screwed it in only to find it wouldnt start anymore (and still leaked) so i took it out only to find its some sort of foo foo widget valve:doh: and at a guess me tightening it up stopped it starting - so after lunch i'm gonna replace the 2 seals in it and refit it and hopefully it will, start, not leak and i'll do a video
got the petrol to the carb and it fired up almost 1st go (too quick for a video pete) but fuel leaked out of the bottom of the carb - i thought it was a drain plug so screwed it in only to find it wouldnt start anymore (and still leaked) so i took it out only to find its some sort of foo foo widget valve:doh: and at a guess me tightening it up stopped it starting - so after lunch i'm gonna replace the 2 seals in it and refit it and hopefully it will, start, not leak and i'll do a video
Attachments
CarlosVanDango
Active Member
- Posts
- 197
- Location
- Rotherham
here we go 1st time it's run since 1992 my phone ran out of memory but i was about to mention the wobbly dissy cap - not sure whats up there
needs a starter solenoid as the tab has broke off, but apart from that no leaks the new seals on the carb part (whatever it was) have cured it, and starts 1st turn of the key (well push of the spanner)
i need to bleed the clutch better now as it stalled when i selected gear but so far so good
ok can't upload the video whats this mean
my phone ran out of memory but i was about to mention the wobbly dissy cap - not sure whats up thereneeds a starter solenoid as the tab has broke off, but apart from that no leaks the new seals on the carb part (whatever it was) have cured it, and starts 1st turn of the key (well push of the spanner
)i need to bleed the clutch better now as it stalled when i selected gear but so far so good
ok can't upload the video
whats this mean
CarlosVanDango
Active Member
- Posts
- 197
- Location
- Rotherham
bled the clutch so i'm certain its free of air but still it drags so it must be the plate siezed - any tips on the best way to free them without stripping it?
gonna try sitting it on axle stands and running it and hit the brakes to see if it frees off - worth a try as i can check the 4wd too
gonna try sitting it on axle stands and running it and hit the brakes to see if it frees off - worth a try as i can check the 4wd too
pocketrocket
Active Member
- Posts
- 658
- Location
- sheffield
bled the clutch so i'm certain its free of air but still it drags so it must be the plate siezed - any tips on the best way to free them without stripping it?
gonna try sitting it on axle stands and running it and hit the brakes to see if it frees off - worth a try as i can check the 4wd too
You can check your freewheeling hubs while your there too
