:rolleyes:
must be a general unwritten rule then :eek:

General guidance, don't run three cylinder motorcycles with only the headers attached ..

Kawasaki KH250 when I was 17 .. those were the days .. and had to remove the silencers for some reason. Started it up and thought it was a tad loud in the garage, so took the centre stand off (so it wouldn't hit the chain) and went for a blast, as you do. Unfortunately the centre exhaust header pointed directly towards the rear tyre and I had to wait at the railway crossing, giving it some blats 'just to keep it running, like' .. set off with some gusto, melted tyre, biiiig sideways slide, just held it, pulled into the side, **** taken all round!

Change of underwear needed nurse .. ;)
 
Yeah so I did a test of my winch under load and, urm, YEP it's still fast!! :eek:

Off roading tomorrow WOOP WOOP :D
 
Don't forget the photos after your off roading and a performance analysis. :). Just pass over the petrol costs, though. :D. Enjoy the day!
 
Sam

Have you reconditioned that budget 12000lb winch yet?

If not, is there any chance you could post a step by step as I want to refresh mine and could do with some hints

Cheers Rob
 
Hello everyone :)

Well, today was a day!

From the start, got to parkwood nice and early and had a Butty. Pretty cold and light snow.

At 9.30 was one of the first into the site, and went directly for the big pond which was deep today, wanted to test out the Megasquirt!

Plunged in and got heroically stuck in the middle, not sure if we were floating too much or too much silt but tried from both directions and couldn't get through the middle 5 feet!

Anyway, here's a shot pretty deep, water gushing in fast, but still ticking over sweet as a nut. Impressive!

1118B190-018F-42CC-86EA-AEB03B987FEB-224-00000006916260A0.jpg


So we carried on off roading with the heaviest of right feet having a great time, burning lots of petrol no doubt!

Used the winch a couple of times when I ran out of talent and yes it was great, in fact it was all going swell until:

2995A512-A38E-43DC-886E-BA6DDD12BF27-224-0000000695D0F535.jpg


D8C6D22C-01A6-4197-9A08-A97057B0ADFD-224-00000006A7D5D8EC.jpg


Oh dear, not again :(

Has been a couple of years since this last happened:

067FDD9B-7734-4204-8148-E097B3CF3332-224-00000006B2B05BE4.jpg


Now after it happened last time I vowed to always carry all the spares I could need in the car to repair it, and with that in mind we had a good laugh about it to get us ready for the job that ensued.

Luckily my passenger today was my good friend Mike who is also an excellent mechanic/engineer so we were really able to work at this together.

With a collection of hi-lift, winch off tree and bottle jack we were able to repair the car safely.

We started at 12.30 and finished at 4.00pm. We had to employ some pretty ghetto bush repair techniques along the way but the result was a replaced swivel ball which had been done as good and as clean as it would have been in my workshop.

We decided to spend the extra time washing everything properly in our parts washer (empty spares box swilled with petrol) so they it wouldn't need re-doing at home.

This took time but was worth it!

Not got many pics because the mixture of 4" deep slop and **** and Land Rover swivel grease pretty much had the hands out of action the whole time.

Perversely it was good fun doing it though and a huge sense of achievement to drive the car out of there without borrowing a single tool, spare or lent hand from anyone else:

88A91B26-E845-4A6F-9649-43A7558ADB85-224-00000006BCEEC498.jpg


A569225E-4167-472F-A2E2-C7F23CBDFE8F-224-00000006C4BB6854.jpg


FF9CBA55-44D7-4BDE-A6FF-63A478526338-224-00000006CB5B2BAE.jpg


Not a clean workshop:

26C949D1-2107-491D-8AA6-8BFE48624F63-224-00000006D1F7AA15.jpg


But it came together after a while:

F40FF64E-F547-4E21-8C23-1F1E87CC4C4E-224-00000006DE457549.jpg


Bastard things (picture taken on the drive at home!):

901C2083-5CCA-45BA-8561-173595FACCD0-224-00000006D8DB168C.jpg


Cheers!
 
Sam

Have you reconditioned that budget 12000lb winch yet?

If not, is there any chance you could post a step by step as I want to refresh mine and could do with some hints

Cheers Rob

Hello pal.

Not just yet tbh, turns out I had forgotten I am still after a couple of bits for that one so will have to get round to it.

It is half done though so not ideal anyway.

I can help you through it no problem though :D

It's welding the brake that you may have more fun with!
 

Similar threads