Ianwallace said:
It's coming up with a load of message on the dash.
Traction
Eas
Air con light
Click to expand...
There is no Air Con light on the dash??!!??!!

You sound as if you have a serious electrical issues...

Are you positive the battery is fully charged and healthy?

Take a sniff at the under bonnet fuse box, if it smells burnt, then that could be the issue!
 
The air con lamp is on the hvac unit. I'm getting this on one of my logs
ImageUploadedByTapatalk1421680734.706098.jpg
 
Ignore the eas fault and the aircon fault for now, they can be sorted later....and you dont have serious electrical issues...just a couple of sensor faults ... Thought you meant the dash was going crazy...

The first could inducate it is out of sync....

You'll have to find the resync process to get the Engine ECU to talk with the BeCM....search on here and read the instructions....
 
With ignition in position 2. Go to engine type EDC, Thor or Gems. Go to last page "UTILITY". Select this. Press "Security learn" diesel or "Learn security code" petrol. Switch off then on again engine should start. Told you not to play until you knew what you were doing.
 
I think I've got a flat battery now.
I don't understand any of this
Saturday all I did was reset all the fault codes and everything was fine. Saturday I used the car all day and had no problems
Sunday I didn't use her all day and today she won't start. So I don't know how I could have done anything.

Anyway I think my battery is dead now as I've done the above and it still does not work and it's a little slow on the turn over.
So I think the battery is low so I will have to get some jump cables.
My unit has different options
ImageUploadedByTapatalk1421683694.181190.jpg
 
Ianwallace said:
I think I've got a flat battery now.
I don't understand any of this
Saturday all I did was reset all the fault codes and everything was fine. Saturday I used the car all day and had no problems
Sunday I didn't use her all day and today she won't start. So I don't know how I could have done anything.

Anyway I think my battery is dead now as I've done the above and it still does not work and it's a little slow on the turn over.
So I think the battery is low so I will have to get some jump cables.
My unit has different options
View attachment 67853
Click to expand...

What is different about Diesel Security learn and Diesel Security learn? Your ECM will be set robust, can't be changed back to none robust once it is. You were not advised to press anything other than Security learn. :);)
 
I haven't pressed them I've only pressed security learn button

I've pressed the following in this order

R-rover p38
Edc
Edc
Utility
Security learn
 
There is another way of doing this if security learn does not work. Look in the "How to" section for more details. Read the security code from the engine ECM note it. Go to BECM and look what it thinks the security code is, it maybe scrambled. Delete that and enter the one noted from the ECM into BECM. Go back one page and press write settings. Engine should start.
 
Hi
The code is correct
My battery is definitely flat now. It's cum up with a message saying engine locked now. Will have to get some leads to give her a jump
 
Battery going flat overnight is either a poor battery or battery drain. with a low battery you will get all manner or fault messages.
 
Don't know the history of the battery so ????
Might be best to buy a new one then? Do I need a special battery for this thing?
 
Ianwallace said:
Don't know the history of the battery so ????
Might be best to buy a new one then? Do I need a special battery for this thing?
Click to expand...
A bloody big one:eek: Battery Megastore on line 130AH 1000CCA about £98 delivered. If you get it started, check your alternator is charging, 14.2/14.5 volts at 2K rpm. Also worth getting a free drain test at Halfrauds before you fork out your hard earned.
 
Charge battery before anything

Bearing in mind you said you pressed a load of buttons, it might be worth checking in the Becm/settings/options/engine - that it is set to the correct edc or edc advanced, what year is your car.
 
dashwoodlandy said:
Charge battery before anything

Bearing in mind you said you pressed a load of buttons, it might be worth checking in the Becm/settings/options/engine - that it is set to the correct edc or edc advanced, what year is your car.
Click to expand...
Lets not worry the poor chap needlessly as I don't think he has blindly pressed buttons!

A Range Rover with a suspect battery is not a good place to start when trying to diagnose things....

The first thing anyone should do when fault finding is have a KNOWN good battery and a decent charge from the Alternator...then go from there.
 
It's a 1999 she's an old one. I don't mind buying a new battery

It it worth buying a cheap one or an expensive one

I've just seen on in halfords for £175
 
Ianwallace said:
It's a 1999 she's an old one. I don't mind buying a new battery

It it worth buying a cheap one or an expensive one

I've just seen on in halfords for £175
Click to expand...
Datatek pointed out the best (and biggest) battery that will fit....£98 130Ah 1000CCA job...and its a beast!
 
You must log in or register to reply here.

Similar threads

F
2001 P38 2.5 Diesel EKA Via NANOCOM
2
Replies
35
Views
1K
Datatek
Datatek
DollyBird
Engine disabled, keys not working, tried the guide “Re-synching the Range Rover P38 diesel engine with the Solved - BECM using a Nanocom” no luck
Replies
9
Views
689
DollyBird
DollyBird
MrGorsky
P38A Occasional "Engine Disabled Press Remote" message on dash.
Replies
19
Views
889
Datatek
Datatek
L
Freelander 2 (LR2) Freelander 2 Stereo replacement (5 inch screen)
Replies
2
Views
151
Nodge68
Nodge68
awkwardbob
L322 2003 HSE radio connectors
Replies
4
Views
583
awkwardbob
awkwardbob