Ianwallace
Active Member
Don't you have to format the card in a special way
Datatek
Well-Known Member
Useful if you write down the codes, then you might get an explanation. I'm not aware of the existence a Pollen Motor fault.
biggeeeee
Retired - Living the dream
Ianwallace
Active Member
I will next time. Was to busy pushing buttons and having fun to think to wright this stuff down 😟
biggeeeee
Retired - Living the dream
Ianwallace
Active Member
Good idea.
I've just been out in the cold this morning having a play. And everything is clear no faults at all. So I'm guessing that they could be very old faults.
If there was a problem I guess they would come up again.
And no (alarm fault ) message
I've just been out in the cold this morning having a play. And everything is clear no faults at all. So I'm guessing that they could be very old faults.
If there was a problem I guess they would come up again.
And no (alarm fault ) message
Ianwallace
Active Member
Does anyone know if you can reset the service counter?
Only if it's a NAS spec BECM.
Ianwallace
Active Member
How can I tell if I have the nas?
You won't have NAS is North American Spec.. Look under market in BECM in diagnostic mode. Should say "market set" certain things can only be changed with different market settings. Personally i would't play with it. Read through the P38 BECM instructions from the Nanocom home page under downloads.
No. Blackbox try to cover their arses for every eventuality but mine was just a standard format as received and worked OK. There might be a limit on the size card it can read. The cards are dirt cheap these days anyway. If the card is corrupt then you could try reformatting. Never ever defrag an SD card or thumb-drive.
ovalandrover
Well-Known Member
The unit says its recording to the card but when it comes to reading the card there's nothing on it, no folder or files.the card works ok in the computer and has been formated
biggeeeee
Retired - Living the dream
Ian,
Had a look round the Nanocom site this morning.
On the Emulator tab at the top of the page, you can access every menu on the Nanocom and click on any of the menus to see what they do.
Useful if you are apprehensive of plugging yours into your vehicle and pressing buttons
Home Page - NANOCOM Evolution
Had a look round the Nanocom site this morning.
On the Emulator tab at the top of the page, you can access every menu on the Nanocom and click on any of the menus to see what they do.
Useful if you are apprehensive of plugging yours into your vehicle and pressing buttons
Home Page - NANOCOM Evolution
TVRConvert
Member
Does the SD card have a write protect tab/switch?
If so try sliding it and then try to record to it again.
If so try sliding it and then try to record to it again.
Ianwallace
Active Member
Urgent help needed
I don't know what I have done but now my car will not start. [emoji53][emoji53][emoji53][emoji53][emoji53][emoji53]
I don't know what I have done but now my car will not start. [emoji53][emoji53][emoji53][emoji53][emoji53][emoji53]
Battery is flat because you have faffed with it for too long without charging it or going for a good long run ...
Ianwallace
Active Member
Battery is fine
Sounds like it could have gone out of sync.....good thing you have the Nanocom!!
Now trouble is I have no idea how to do the re-sync...
But it involves reading the code from the BeCM and inputing into the Engine ECU (or the other way around)
Wammers/Datatek will know as they have Diesel P38's and also the Nanocom!
Don't panic, you currently own the best diagnostic tool there is for the P38!
biggeeeee
Retired - Living the dream
Ianwallace
Active Member
It's coming up with a load of message on the dash.
Traction
Eas
Air con light
Traction
Eas
Air con light
