What have you done to your Landie today.

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Hi all
Just had a bad day replacing the tailgate window mechanism and motor on my newly bought freelander1 td4 3dr, never new these things needed so much work, finished it all off, was mega chuffed only to find the darn window doesnt slot in properly at the top it seems to sit out side the top rubber.:mad: not happy, enyone had the same issue?????
 
Got round to fitting my new stainless flo-flex bump stops, along with stainless bolts :D what a suprising pain in the arse it was to do the front O/S one, everything was working against me :D
Also took off the front grill, grill surround and driving lights to see if the allard intercooler will fit, it won't fit and it isn't actually much bigger than my standard on when I studied it closely, so it's not worth getting it to fit when it probably wont improve anything much :rolleyes: Decided I'm going to get an allisport large intercooler in a few months instead :D
 
I broke it....... Changed the rear windscreen wiper. While reattaching the spare wheel to the carrier I sheeted on of th bolts off. Gutted oh we'll have gone to B&Q and have purchased an M8 replacement will drill out the old one and replace this weekend. Rear wheel is being held on by the other two bolts. So far no screams from cars behind squished by it falling off.
 
cleaned headlining finished painting chasis sides got the cb working clean swivel area ready to change the fluids thanks buster for a very useful thread
 

Attachments

  • 2011-06-26 14.44.16.jpg
    2011-06-26 14.44.16.jpg
    137.8 KB · Views: 191
  • 2011-06-26 14.44.27.jpg
    2011-06-26 14.44.27.jpg
    196.4 KB · Views: 213
Snapped the ****ing gear stick of on the series yesterday, jammed it in 3rd and drove home. Took it off and welded it, the wrong way round! :mad:

Cut it off and tried again and it all went wrong so gave up, tried again today and the ****ing welder has run out of gas! :mad: :mad: :mad:
 
bought it a donor, rotten sills, and arches but seats hardly look used, 130k on clock, no smoke, pulls well and sounds good. Will be breaking at some point. Ok for the money. 12 monthes tax and 3months mot.:D
 
5284f893-c6a3-394c.jpg
This....

One down one to go. Then some covers on cos they are vile.
 

Attachments

  • uploadfromtaptalk1332004792512.jpg
    uploadfromtaptalk1332004792512.jpg
    72.1 KB · Views: 221
  • uploadfromtaptalk1332004812616.jpg
    uploadfromtaptalk1332004812616.jpg
    66.8 KB · Views: 199
Installed a cosmetic mod, a protection mod and a tacky mod!

Cosmetic - Raised intake on N/S wing
Protection - Bearmach bumperettes
Tacky - 2 Tricolours for Paddy's day

The raised intake was a doddle. It came undrilled which suits me fine and makes for a far better fit.

The tricolours were push fit and very cheap and tacky!

The bumperettes were a bit of a **** to be honest as I used loose (stiff) nuts in the hollow section of the rear crossmember. I had to grind a spanner down to get to the nuts. They feel very strong though, look good and should help protect my rear lights. I also had to cut a small notch in the mudflap hangars but they are fairly discreet.
The checker plate on the bumperettes isn't finished very well as the edges are razor sharp and haven't been de-burred or chamfered which is a shame. I cant risk doing it myself as the coating on the bumpers might suffer.
If I get a quiet day in the summer I might drill the rivets off and chamfer them myself but there's so much else to do!
 

Attachments

  • Spanner.JPG
    Spanner.JPG
    55.3 KB · Views: 204
  • Twig tricolour.JPG
    Twig tricolour.JPG
    54.6 KB · Views: 220
  • Tricolour.JPG
    Tricolour.JPG
    40.4 KB · Views: 202
  • O.S After.JPG
    O.S After.JPG
    215.5 KB · Views: 202
  • Offside before.JPG
    Offside before.JPG
    214.4 KB · Views: 194
  • Nearside before.JPG
    Nearside before.JPG
    217.4 KB · Views: 202
  • N.S Wing after.JPG
    N.S Wing after.JPG
    44.1 KB · Views: 198
  • N.S Wing before.JPG
    N.S Wing before.JPG
    46.5 KB · Views: 196
These are the pictures I should have attached!:eek:
 

Attachments

  • LHS Before.JPG
    LHS Before.JPG
    34.3 KB · Views: 176
  • RHS Before.JPG
    RHS Before.JPG
    36.4 KB · Views: 199
  • N.S After.JPG
    N.S After.JPG
    207.9 KB · Views: 195
  • O.S After.JPG
    O.S After.JPG
    215.5 KB · Views: 178
Removed the rear seats, loadspace liner, subwoofer and rear 6x9's so I could give the back a good clean, got everything clean and it decided to start ****ing down, so I gave up, will put all back tomorrow, and think of a better idea to mount the rear 6x9's :D
Also removed the chequer plate sill protectors and rear quarters to clean behind them, think I'm going to buy aluminium bolts to stop that damn corrosion :rolleyes:
 
Back
Top