was trying to also work out what that meant, lol
Other what have u done on ur disco today
- Thread starter gstuart
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
was trying to also work out what that meant, lol
Magicgrotto
Well-Known Member
- Posts
- 2,769
- Location
- doncaster
GREAT MINDS THINK ALIKE !!
biggeeeee
Retired - Living the dream
- Posts
- 11,090
- Location
- Lanarkshire or Argyll
so are u now saying my temp sensor is ok now,
Was simply a stab at humour as its always colder here, forget it!
biggeeeee
Retired - Living the dream
- Posts
- 11,090
- Location
- Lanarkshire or Argyll
Yip - IID shows a fault with both which can't be cleared when they are blanked. Was done before I bought it.
biggeeeee
Retired - Living the dream
- Posts
- 11,090
- Location
- Lanarkshire or Argyll
neilly
Well-Known Member
- Posts
- 20,000
- Location
- Oxfordshireness
I'm sure there is an alternative saying to that one
shhhssshhh, @biggeeeee , leave them in their delusions, they are happy like that and playing quietly.
Cheers
u expect my simple brain after today to keep up
biggeeeee
Retired - Living the dream
- Posts
- 11,090
- Location
- Lanarkshire or Argyll
u expect my simple brain after today to keep up
How many cups of T did you make?
thks, sounds like u need the iid patch done then , thought that was just for eu4 engines and post 2008 that needed the patch
been recommended when mine are done to leave the pipes in situ so that when it's in for a mot they can't tell if they've been blanked or not,
i did actually , thought it was the least i could do in making the tea,
also gave them a tip to have a few pints on me, seeing they done such a cracking job,
think it always goes along way
Littelwill
Well-Known Member
- Posts
- 3,065
- Location
- Lincolnshire
Bit of a long shot. But I don't suppose any of you guys are in the Norfolk area this weekend are you? My D3 is cocking a leg after I replaced the rear upper suspension bush. I moved the height sensor whilst fitting new the new arm!! Does anyone have an IID tool who knows how to recalibrate the suspension heights? Beer tokens available...
Thanks
Thanks
guy selling some short roof rails dropped some off today , as he didn't want them any more
about time i lucked out, as he only wanted £20 for them
need a bit of a clean and tidy up ,
will be perfect to mount a cb aerial onto them
see u can even get the rubber grommets seperate that end up brittle
are the same rubber grommets used on the D2
http://www.brit-car.co.uk/product.php/84012/0/roof_rail_blanking_plug_discovery_2
about time i lucked out, as he only wanted £20 for them
need a bit of a clean and tidy up ,
will be perfect to mount a cb aerial onto them
see u can even get the rubber grommets seperate that end up brittle
are the same rubber grommets used on the D2
http://www.brit-car.co.uk/product.php/84012/0/roof_rail_blanking_plug_discovery_2
hi mate
did u put a jack under the suspension and set the height correctly , otherwise it will destroy ur new bushes
assume u changed both sides
alas the iid tool won't reset another suspension on another vehicle , costs £60 to get another vin unlocked
would be worth getting an iid tool, will pay for itself in know time at all
would be very happy to plug my iid tool in for u FOC , but won't adjust the suspension i'm afraid
as it's locked to my vin, however it will read and clear faults
how are u getting on
biggeeeee
Retired - Living the dream
- Posts
- 11,090
- Location
- Lanarkshire or Argyll
Jammy bu66er. I paid £80 for mine.
Just been out and fitted my genuine roof bars that I picked up, I've added old ski brackets to it as they hold my ladder lovely. (Coz its stopped raining)
biggeeeee
Retired - Living the dream
- Posts
- 11,090
- Location
- Lanarkshire or Argyll
No doubt postage will be £5 or £6 though!
@Littelwill
found this excerpt for u , from someone else who has replaced the rear upper wishbones
Use a jack under the shock absorber and jack the assy up so that a distance of 485 mm between the center of the drive shaft and underside of the wheel arch is obtained. As the body in my case still was slightly raised I measured that the spacer was 50 mm thick and the body was 55 mm over the chassis mount. So in my case I adjusted the distance to be 490 mm to accomodate the extra 5 mm. I expect this might not to be super critical as the procedure merely is to remove stress from the bushes and thus premature failure by fastening the bolts with both arms in normal operation height/position.
found this excerpt for u , from someone else who has replaced the rear upper wishbones
Use a jack under the shock absorber and jack the assy up so that a distance of 485 mm between the center of the drive shaft and underside of the wheel arch is obtained. As the body in my case still was slightly raised I measured that the spacer was 50 mm thick and the body was 55 mm over the chassis mount. So in my case I adjusted the distance to be 490 mm to accomodate the extra 5 mm. I expect this might not to be super critical as the procedure merely is to remove stress from the bushes and thus premature failure by fastening the bolts with both arms in normal operation height/position.
no he dropped them off in person this morning
they need a little rub down and a quick spray , but to be honest won't see them anyway so not to bothered with a few marks here and there
as i've got to remove the end caps to fit a cb aerial bracket i've just soaked the bolts in plus gas , will leave it to soak in for a few days
got some new stainless steel bolts and washers to replace the old bolts
makes a change for me to get a little bit of luck in getting these roof bars cheap
biggeeeee
Retired - Living the dream
- Posts
- 11,090
- Location
- Lanarkshire or Argyll
Meant for the bits from brit car
