- Posts
- 19,299
- Location
- Buckinghamshire, UK. ('95 DT)
Misfire issue, not the airlock / gas in coolant issue.
What did you do with your Range Rover today
- Thread starter Dopey
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Datatek
Well-Known Member
- Posts
- 44,909
- Location
- Near Poitiers SW France
And if the misfire is due to coolant ingress to the cylinder or loss of compression?
- Posts
- 19,299
- Location
- Buckinghamshire, UK. ('95 DT)
Little light that connects instead of the fuel injector and flashes with each pulse from the ECU. If not pulsing then no power going to infector so no fuel and hence the misfire.
- Posts
- 33,620
- Location
- North Shropshire
Doing some research.. it seems the only cost viable route is to buy a top hat block and swap all the bits off mine myself.. problem is i don't have the space to do it.
Other options eg getting someone else to do it seem to be too expensive, especially as my motor isn't a pristine example to start with
Other options eg getting someone else to do it seem to be too expensive, especially as my motor isn't a pristine example to start with
I had the kick panel out and the grounds are all nice. I did have a bit of corrosion with the black plug, but cleaning it up did nothing.
I assume when it broke on you the wire broke but the outer coat didn't?
Datatek
Well-Known Member
- Posts
- 44,909
- Location
- Near Poitiers SW France
23108924
Well-Known Member
- Posts
- 131
- Location
- Shropshire
Maybe a bit basic but.... do you have power into the door? follow that first, is it BECM controlled? I don't know.
But you have a spares car available dont you.
J
EXCUUUUUUUUSE ME? HE HAS A WHAT??
RangeRoller dt
Well-Sprung Member
- Posts
- 14,396
- Location
- Trapped inside my head @ LZ asylum
RangeRoller dt
Well-Sprung Member
- Posts
- 14,396
- Location
- Trapped inside my head @ LZ asylum
Get whole Thor engine for £7/800 Kermie
I might need to borrow a DVM from work then. I really don't trust mine.
The door is BeCM controlled. Sorry about the photo of a screen. I assume the break would be between C1383R and the door outstation. My Halfords special DVM just doesn't seem to give consistent results, so putting a halt to progress somewhat.Maybe a bit basic but.... do you have power into the door? follow that first, is it BECM controlled? I don't know.
But you have a spares car available dont you
J
I do not have a spares car available. And I love my wife and her car more than life itself.
- Posts
- 33,620
- Location
- North Shropshire
Did that last time.. was never right and not exactly lasted long
Datatek
Well-Known Member
- Posts
- 44,909
- Location
- Near Poitiers SW France
Used the project car to test a new EAS cable
- Posts
- 33,620
- Location
- North Shropshire
As a quick fix to get mobile and give me time to think what to do, going to drill the thermostat so it doesn't get fully up to temp as that's when it leaks
RangeRoller dt
Well-Sprung Member
- Posts
- 14,396
- Location
- Trapped inside my head @ LZ asylum
I had a spare outstation, so chucked that on. Still no dice.
RangeRoller dt
Well-Sprung Member
- Posts
- 14,396
- Location
- Trapped inside my head @ LZ asylum
Try rubbing them with broccoli
Jon Dor
Well-Known Member
- Posts
- 1,672
- Location
- Beverley, East Riding of Yorkshire
Try calling William up in Lincoln, Kermit. He may have a complete lump.
His mobile: 07903 167575
Good luck...it's time your fortune changed.
Mike.
Datatek
Well-Known Member
- Posts
- 44,909
- Location
- Near Poitiers SW France
