What did you do with your Range Rover today

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Found the reason for the squeaking noise.
1, it appears the hydraulic tensioner is leaking so that needs replacing.
2, It also appears that when the belt came off it has sheered off a bolt. I'm not sure on the name of the part but starting from the front of the engine you have the fan, that is connected by a rod to a pulley that is driven by the aux belt. Well it is that pulley that is missing a bolt head. You can see the black rubber marks where the belt hit it and the clean surface of the broken bolt which suggests it was a recent thing.

So fark!
 
Some big trips coming soon so... Put two front Arnotts on and replaced all the brake disks and pads. Then replaced the pollen filters and all the interior bulbs with LEDs (what a difference, wish I had done this earlier)
Helps to have a mobile full lift wheels free ramp..

016_zps42f02a7f.jpg
 
Last edited:
stevef1964 said:
Stopover, what interior LEDs did you use?
Click to expand...
250822565639_1.jpg
390219690265_4.jpg
230827638047_1.jpg
250881936190_1.jpg


I got these from ebay. I did a search on 'Vehicle Parts & Accessories' then 'Car Parts' and just put in LED, massive selection. The 8 SMD Can Bus was the best to the dome light (Centre interior light) but is 42mm so had to bend the contacts a little) the two rear festoons were replaced with the 16 led LEON perfect as they are 38mm which is the best size for replacing the festoons. I went for Brilliant White and the result is spectacular but you can have other colours. The puddle lights are the AUTO-LIGHTS ones. I have removed the load space bulb as I haven't found a good replacement yet, its useless as a light anyway. Still to do the foot lights. But very much like the LEDs better light, longer lasting (claimed 50,000 hours!) and half the voltage.

I haven't used the other festoons (custom Festoon) yet as they were slow to arrive but have them in reserve.
 
Last edited:
Hi Stopover,

I have a similar set up for my interior lights & must say the lighting is a huge improvement. However, PO fitted LED sidelights that throw a fault everytime i turn the lights on, i've seen canbus lights on ebay, are canbus able to eliminate the fault or should i just fit standards?
 
martynv8 said:
Hi Stopover,

I have a similar set up for my interior lights & must say the lighting is a huge improvement. However, PO fitted LED sidelights that throw a fault everytime i turn the lights on, i've seen canbus lights on ebay, are canbus able to eliminate the fault or should i just fit standards?
Click to expand...

Yes, you need CanBus type LEDs to stop the fault messages. The interior ones inc puddle bulbs are not on the canbus as far as I know, I have no error messages but the exterior bulbs are.
 
I use a 36 LED for my dome light, I chose it because it came with a spring loaded festoon so could be compressed to fit any size fitments. Upto 60mm and down to about 20mm. Although it was wired backwards from factory (Chinese QA for you), so that needed amending. But otherwise it is top kit.

Although it dose generate some heat after 10mins of illumination, which is mildly concerning.
 
Swear at it again. The hydraulic tensioner has finally given up on me. Was about 5 miles from home when the PAS became heavier and the belt squeech increased quite a lot. Bloody part hasn't arrived yet either. >.<
 
You must log in or register to reply here.

Similar threads

A
Range Rover L322 - not turning over
Replies
12
Views
1K
gold rover
gold rover
B
L320 range rover sport 3.0 tdv6 loosing power steering fluid
Replies
3
Views
496
Mark Piercy
Mark Piercy
F
1980 Range Rover 2 door v8 to 300tdi
2
Replies
20
Views
1K
Grrrrrr
Grrrrrr
T
Non start
Replies
3
Views
712
Datatek
Datatek
T
Fan Clutch??
Replies
14
Views
790
Grrrrrr
Grrrrrr
Back
Top