- Posts
- 34,072
- Location
- North Shropshire
i'll see if SDD can give me software versions. currently not seen anywhere to apply any updates, but downloading in the first place is likely the stumbling block
What did you do with your Range Rover today
- Thread starter Dopey
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
- Posts
- 34,072
- Location
- North Shropshire
Lots of error codes today;
Linbus A
Linbus B
Key transponder
Lost comm to audio unit
Lost comm with epb
Linbus A
Linbus B
Key transponder
Lost comm to audio unit
Lost comm with epb
- Posts
- 19,317
- Location
- Buckinghamshire, UK. ('95 DT)
You might as well have put that in Cyrillic script.
Broken wire sonewhere in the canbus thingy?
- Posts
- 34,072
- Location
- North Shropshire
Yes i think that's likely. The diag recommends doing a vehicle factory reset.. reluctant to do it though as i don't know what it actually means
kds
Well-Known Member
- Posts
- 2,271
- Location
- old,ugly, tired in Lincoln.
Disconnect battery wait 5 minutes then touch positive and negative cable on car together for few seconds simple, it will power down everything so everything restarts works in few cars nowadays had to do it not long ago on friends Mondeo when remote wouldn't talk to car after battery change.
- Posts
- 4,678
- Location
- Rotherham
If you remember short while ago got drivers side blower working . Today took of passenger side one and rebuilt a good un out of the bits and pieces. Wow never realised they could blow so much. Even re circulation flaps are working now. Air con a tad low on pressure so ordered new top up can and touch wood (please LR gods) everything should be working as it should 
badfluffy
Well-Known Member
- Posts
- 2,286
- Location
- northampton
picked up the new dual mass flywheel for the l322
- Posts
- 12,669
- Location
- Sud ouest France !
What did that set you back?
- Posts
- 12,669
- Location
- Sud ouest France !
Off to see a land-rover Saturday 
..
On English plates so it may go for parts unless it's wanted for someone else to go through the bother of French plating it... It's a nightmare now over here and expensive to boot
..On English plates so it may go for parts unless it's wanted for someone else to go through the bother of French plating it... It's a nightmare now over here and expensive to boot
badfluffy
Well-Known Member
- Posts
- 2,286
- Location
- northampton
no idea untill they send the bill to the accountantWhat did that set you back?
Datatek
Well-Known Member
- Posts
- 45,063
- Location
- Near Poitiers SW France
Work of the devil, I replaced the DMF on my Transit with a solid flywheel and a special clutch assembly.
If its cheap enough it has a lot of valuable parts in the EU.Off to see a land-rover Saturday
On English plates so it may go for parts unless it's wanted for someone else to go through the bother of French plating it... It's a nightmare now over here and expensive to boot
Have to agree its a bit of a minefield since the B word.
J
badfluffy
Well-Known Member
- Posts
- 2,286
- Location
- northampton
been trying one of those on it for last 6 months going back to dual mass
Datatek
Well-Known Member
- Posts
- 45,063
- Location
- Near Poitiers SW France
Why? Did you fit the correct clutch with the solid?
badfluffy
Well-Known Member
- Posts
- 2,286
- Location
- northampton
came as a complete kit, took 3 attempts to even get it fitted right
- Posts
- 12,669
- Location
- Sud ouest France !
Certain vehicles don't take to the vibration from the engine.
Our Volvo v50 has a solid conversation kit and rattles the crap out of the gearbox.. That's going back on a dual mass flywheel and clutch when the time is right
- Posts
- 12,669
- Location
- Sud ouest France !
1500€
b word is right
Datatek
Well-Known Member
- Posts
- 45,063
- Location
- Near Poitiers SW France
That doesn't sound good. The Transit one went straight on no problem, it's been there a long time now, £280 for the solid kit, close to €1000 for the DMF kit over here so no contest.
5 cylinder?Certain vehicles don't take to the vibration from the engine.
Our Volvo v50 has a solid conversation kit and rattles the crap out of the gearbox.. That's going back on a dual mass flywheel and clutch when the time is right
Datatek
Well-Known Member
- Posts
- 45,063
- Location
- Near Poitiers SW France
A spare HEVAC? It was never cheap registering a car in France but with all the emissions crap it is now very expensive.Off to see a land-rover Saturday
On English plates so it may go for parts unless it's wanted for someone else to go through the bother of French plating it... It's a nightmare now over here and expensive to boot
If you buy it to break, I might be interested in the rear bumper if it's the twin exhaust model
- Posts
- 12,669
- Location
- Sud ouest France !
4ctl 2.0 hdi peugeot engine Keith
