- Posts
- 724
- Location
- Lincolnshire
Ah, mon Dieu, had to get rid of the precious caravan. Didn't go down with the kids well. They wanted to blow it up, proper Top Gear style 
What did you do with your Range Rover today
- Thread starter Dopey
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
jonesavpman
New Member
- Posts
- 102
- Location
- Middle of nowhere,close to Rotherham
Datatek
Well-Known Member
- Posts
- 44,887
- Location
- Near Poitiers SW France
Looks good with your trim colour.
Littelwill
Well-Known Member
- Posts
- 3,065
- Location
- Lincolnshire
^^ looks good well done!
mutsnutz
Well-Known Member
- Posts
- 1,964
- Location
- pink panther country
looks very nice mate gives it more of a modern look to it :jaw:
:jaw:
Last edited:
blackstrat
Well-Known Member
- Posts
- 9,265
- Location
- East Anglia
What a great idea! Transforms it matey, nice one!
jonesavpman
New Member
- Posts
- 102
- Location
- Middle of nowhere,close to Rotherham
Thanks to all. It does make the inside a nicer place to sit. before it was just a sea of black with a bit of brown!! The missus likes it too which is always a bonus!!
Next project is to sort out the heating and cooling blend motors are fecked!! Picked up some used but working (alledgedly) ones yesterday, along with a complete heater unit for £30.
The missus likes it too which is always a bonus!!Next project is to sort out the heating and cooling
blend motors are fecked!! Picked up some used but working (alledgedly) ones yesterday, along with a complete heater unit for £30.
mutsnutz
Well-Known Member
- Posts
- 1,964
- Location
- pink panther country
replaced rear shocks got front to do yet while under the range i cleaned up the muck that was on top of the chassis :jaw:
stevebrookman
Well-Known Member
- Posts
- 388
Replaced the front brake pads.
Took nearly 2 hours!
1-Wheels stuck to hub-took ages to free them with my long piece of 3*2.
Cleaned the rim and copper greased before putting back on.
2-Caliper nuts very rusty-cleaned them up with wire brush and file eventually got them out.
3-When pushing one piston in the other came out-used the old brake pad across the two pistons and squeezed with my huge pipe wrench.
Eventually finished the brakes and then decided to fix the blow on the exhaust where the centre box meets the back boxes.
Replaced the back boxes a while back and should have changed the middle at the same time. I may change it as it's only £50 but am currently looking for a L322 Supercharged.
Steve.
Took nearly 2 hours!
1-Wheels stuck to hub-took ages to free them with my long piece of 3*2.
Cleaned the rim and copper greased before putting back on.
2-Caliper nuts very rusty-cleaned them up with wire brush and file eventually got them out.
3-When pushing one piston in the other came out-used the old brake pad across the two pistons and squeezed with my huge pipe wrench.
Eventually finished the brakes and then decided to fix the blow on the exhaust where the centre box meets the back boxes.
Replaced the back boxes a while back and should have changed the middle at the same time. I may change it as it's only £50 but am currently looking for a L322 Supercharged
.Steve.
- Posts
- 16,479
Adjusted the feck out of the handbrake in hopes it'll pass the MOT later!!
L322 handbrakes are notoriously crap!!
L322 handbrakes are notoriously crap!!
ady014
Active Member
- Posts
- 166
- Location
- Wisbech, Norfolk
Located and sorted source of my suspension air leak. First time in my ownership she hasn't sunk to the bump stops overnight! Valve block seal kit ordered to try and sort my other eas issues...
Datatek
Well-Known Member
- Posts
- 44,887
- Location
- Near Poitiers SW France
Don't be shy, tell us where the leak was.
Datatek
Well-Known Member
- Posts
- 44,887
- Location
- Near Poitiers SW France
Edited for accuracy
ady014
Active Member
- Posts
- 166
- Location
- Wisbech, Norfolk
Don't be shy, tell us where the leak was.
From the brand new joiner I fitted to replace the two joins that were there when the exhaust melted the pipe over the axle.... I know I need to run a new pipe
Datatek
Well-Known Member
- Posts
- 44,887
- Location
- Near Poitiers SW France
From the brand new joiner I fitted to replace the two joins that were there when the exhaust melted the pipe over the axle.... I know I need to run a new pipe
- Posts
- 16,479
Edited for accuracy
Woohoo, legal for another year....no advisories...big grins.
(Before some jobsworth comes along and is being pedantic....yes I do know an MoT is only valid at the time of issue and I am legally responsible to ensure it remains legal until the next MoT....
)
ady014
Active Member
- Posts
- 166
- Location
- Wisbech, Norfolk
Put a new alternator belt on as the old one looked iffy, was well past iffy when I took the old one off had a split right through the inside edge Nice easy 5 minute job tho.
Nice easy 5 minute job tho.
- Posts
- 724
- Location
- Lincolnshire
Put a new alternator belt on as the old one looked iffy, was well past iffy when I took the old one off had a split right through the inside edge
Changing the idler pulley is a good idea too. Got rid of my chirping noise especially on tick over.
