200tdi ayre
Well-Known Member
- Posts
- 5,832
- Location
- Ashbourne (sometimes)
Will do, I've been looking over your challenge truck rebuild on Devon and got some ideas from that
but no close ups of the front hoop mount so ill pay attention 
Trailer - challenge truck build
- Thread starter 200tdi ayre
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Will do, I've been looking over your challenge truck rebuild on Devon and got some ideas from that
but no close ups of the front hoop mount so ill pay attention 
- Posts
- 1,692
- Location
- towie hell
that was a nasty build, it needed a new chassis and the owner had stupid requestsWill do, I've been looking over your challenge truck rebuild on Devon and got some ideas from that
200tdi ayre
Well-Known Member
- Posts
- 5,832
- Location
- Ashbourne (sometimes)
Intercooler anyone ?
discomark10
Well-Known Member
- Posts
- 3,977
- Location
- Milton Keynes
Beasty!
200tdi ayre
Well-Known Member
- Posts
- 5,832
- Location
- Ashbourne (sometimes)
Justa bit ! Doesn't actually fit goes about half way across the tyres
this is going in a Tractor puller I've got a squarer one for mine but a similar area
200tdi ayre
Well-Known Member
- Posts
- 5,832
- Location
- Ashbourne (sometimes)
More progress with the roll cage mounts
Gonna do some more supports from the chassis and some triangulation for strength
Overkill
Also cleaned out the inlet on the head as they were full of crap and made up some brake pipes more to come
Gonna do some more supports from the chassis and some triangulation for strength
Overkill
Also cleaned out the inlet on the head as they were full of crap and made up some brake pipes
more to come
200tdi ayre
Well-Known Member
- Posts
- 5,832
- Location
- Ashbourne (sometimes)
Plates tacked on
200tdi ayre
Well-Known Member
- Posts
- 5,832
- Location
- Ashbourne (sometimes)
Bit more ...
Wish I'd welded a plate across the crossmember first now but I don't think it's critical
Overkill is the way
Wish I'd welded a plate across the crossmember first now but I don't think it's critical
Overkill is the way
200tdi ayre
Well-Known Member
- Posts
- 5,832
- Location
- Ashbourne (sometimes)
The main hoop is finished
How to make sure your cuts are straight
Brakes are finished and bled
Bleeding machine applies pressure to the system pushing out air so all you have to do is crack off the bleed screws
Design for the front hoop mounts is sorted just gotta make it
How to make sure your cuts are straight
Brakes are finished and bled
Bleeding machine applies pressure to the system pushing out air so all you have to do is crack off the bleed screws
Design for the front hoop mounts is sorted just gotta make it
- Posts
- 1,692
- Location
- towie hell
Bit more ...
Wish I'd welded a plate across the crossmember first now but I don't think it's critical
Overkill is the way
yes you should! its only as good as the weakest part!
200tdi ayre
Well-Known Member
- Posts
- 5,832
- Location
- Ashbourne (sometimes)
After seeing your pic of the one you'd done on the tray back I realised, but it was too late by then :/ but I've got plenty of supporting plates to spread the load, and it's all made out of 10mm
200tdi ayre
Well-Known Member
- Posts
- 5,832
- Location
- Ashbourne (sometimes)
And to e honest I think the tube will break before the mounts or chassis does
mikeyt
Active Member
- Posts
- 299
200tdi ayre
Well-Known Member
- Posts
- 5,832
- Location
- Ashbourne (sometimes)
Bit tidier eigh noisy
Routing the rear rad pipes
How about this for a intercooler
Routing the rear rad pipes
How about this for a intercooler
200tdi ayre
Well-Known Member
- Posts
- 5,832
- Location
- Ashbourne (sometimes)
Rear rad pipes done
Just clears everything without touching just gotta mount it to the chassis
Just clears everything without touching just gotta mount it to the chassis
Mr Noisy
Coming in your ears.
- Posts
- 10,146
- Location
- Altrincham, Cheshire
Yes tis much tidier now.
Hard part is keeping it that way!
Hard part is keeping it that way!
discomark10
Well-Known Member
- Posts
- 3,977
- Location
- Milton Keynes
Dam you and your workshop what did you use for your rad pipes? Is it stainless?
what did you use for your rad pipes? Is it stainless?
200tdi ayre
Well-Known Member
- Posts
- 5,832
- Location
- Ashbourne (sometimes)
Dam you and your workshop
Hehe
it's just standard thin walled mild steel at the moment, to make mountings, welding ect easier as we don't have a TIG, I'm not too worried about it being steel as isn't that what the block is made of ? Ill make one out of stainless eventually though
discomark10
Well-Known Member
- Posts
- 3,977
- Location
- Milton Keynes
Yes but the block is a bit thicker. Should be ok providing the outside is protected
sible88
New Member
- Posts
- 3,492
- Location
- Hertfordshire
Hammerite it
Similar threads
