- Posts
- 58,170
- Location
- Preston Lancs.
You get a fault code with the MAF disconnected? I didn't.
Yes, airflow fault. Don't know about modulation valve never tried with that disconnected.
p38 diesel fault code 33
- Thread starter fredi
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Yes, airflow fault. Don't know about modulation valve never tried with that disconnected.
Datatek
Well-Known Member
- Posts
- 44,623
- Location
- Near Poitiers SW France
I ran for some time with the MAF disconnected, no faults reported, interesting, I'll have another look.Yes, airflow fault. Don't know about modulation valve never tried with that disconnected.
- Posts
- 58,170
- Location
- Preston Lancs.
That's what i got. "Airflow fault" nothing more. If i get a chance will try it tomorrow and see if i can get it again.
- Posts
- 58,170
- Location
- Preston Lancs.
Think someone is playing with your head. With the MAF disconnected you will get an error message, possibly with the modulation valve disconnected you will get and error. But the ECU has no way of knowing that the vac pipe is disconnected. There is no code 33 for the BMW M51 EDC engine. If the Faultmate shows no error there is no error. You are chasing rainbows. Faultmate is the best diagnostic tool for the P38 by a very long way it will even do things the Landrover official tool will not do.
Last edited:
oh wammers i just send a privet message to datatek, showing faultmate is developed for the first diesels, but not working on the latest. If you are interted can send you to. or better we wait for the reaction from datatek.
However we still the key question. I have the latest diesel. And yes I have a serious real error 33......
I just ask if somebody knows it...... It looks like nobody has before. I will find it out. anyway the quick search until now is that i think it is related to egr. I i find I will post the result.
However we still the key question. I have the latest diesel. And yes I have a serious real error 33......
I just ask if somebody knows it...... It looks like nobody has before. I will find it out. anyway the quick search until now is that i think it is related to egr. I i find I will post the result.
Datatek
Well-Known Member
- Posts
- 44,623
- Location
- Near Poitiers SW France
No airflow or IAT info on my Faultmate unless I'm going blind, nor do I get a fault for a disconnected MAFThat's what i got. "Airflow fault" nothing more. If i get a chance will try it tomorrow and see if i can get it again.
- Posts
- 58,170
- Location
- Preston Lancs.
Sorry to have to say this in this area but bollocks. It doesn't matter what diesel you have if it's EGR it's the same bloody ECU. Go to BMW there is NO code 33 listed for the M51 engine. I wash my hands of you.
Datatek
Well-Known Member
- Posts
- 44,623
- Location
- Near Poitiers SW France
How old is your Faultmate? My Faultmate Extreme works fine on my MY2000 diesel.
I was told, but have no evidence to support the statement, that the EDC for the MAF/EGR fitted version of the M51 was a stopgap update of the earlier non MAF/EGR EDC as the common rail M57 engine was already in place to replace the M51 and that no diagnostic data is available for MAF, IAT or EGR. Certainly I can see no airflow or EGR data on my Faultmate Extreme unless I have missed a page of live data information.
- Posts
- 58,170
- Location
- Preston Lancs.
No airflow or IAT info on my Faultmate unless I'm going blind, nor do I get a fault for a disconnected MAF
Nanocom gives a "Airflow fault" if the MAF is disconnected. Faultmate may not but Nanocom does. There is no airflow info or live IAT info shown on Nanocom either because airflow info is inconsequential to the operation of the engine other than for monitoring EGR gas mix. IAT is a preset to ensure EGR operation under all conditions.
Datatek
Well-Known Member
- Posts
- 44,623
- Location
- Near Poitiers SW France
Inlet air temperature is measured by a thermistor in the MAF assembly.
right. egr and maf is not supported on faultmate. See my list on the autodiagnos. I start to check the differences with the temp sensor. It looks like it is just a sensor tolerenance. But when you see for example the fuel is 18 degrees. faultmate gives -10 and autodiagnos gives the right temp (+/- some degrees). Then I find out that more figures presented by faultmate are wrong
May be we can make a new forum item of this point. In my opinion you should not advice people to but faultmate for the diesel
May be we can make a new forum item of this point. In my opinion you should not advice people to but faultmate for the diesel
Datatek
Well-Known Member
- Posts
- 44,623
- Location
- Near Poitiers SW France
If your Nanocom gives an airflow fault, then it might be reasonable to draw the conclusion that it would appear as flash code 33 since there is no airflow fault listed in the flash codes. for you to get an airflow fault, there must be a code. Can you post a screen shot, I'd like to know why it doesn't appear on Faultmate.
Datatek
Well-Known Member
- Posts
- 44,623
- Location
- Near Poitiers SW France
I repeat, how old is your Faultmate and what firmware level is it running?
- Posts
- 58,170
- Location
- Preston Lancs.
Only for the use of the ECU so it can accurately measure the volume of air going through the MAF. A MAF that doesn't know the temp of the air flowing through it cannot measure the mass. We have been here before. Maybe the IAT at the MAF is used as a computing factor by the ECU when comparing preset IAT and engine, fuel temps, to extrapolate actual IAT for fuelling, but as the air from the MAF goes through a turbo charger and an intercooler before it enters the cylinders, using MAF sensed air temp for fuelling would be like wearing an overcoat in St Ives because it's cold in John o Groats.
- Posts
- 58,170
- Location
- Preston Lancs.
Could this be a veiled advert for Autodiagnos by any chance? He is not winning me over to be honest.
Datatek
Well-Known Member
- Posts
- 44,623
- Location
- Near Poitiers SW France
Not sure really, I did find some errors with temperature readings on Faultmate but a firmware update corrected them. Not used the Faultmate a lot but never had any reason to suspect most of the readings.Could this be a veiled advert for Autodiagnos by any chance? He is not winning me over to be honest.
tomcat59alan
Well-Known Member
- Posts
- 18,611
- Location
- wirral and triquivijate
Could this be a veiled advert for Autodiagnos by any chance? He is not winning me over to be honest.
And he has no sense of humour.
- Posts
- 58,170
- Location
- Preston Lancs.
Yes same with Nanocom. Which reminds me must have a look for any updates, but i think most of the teething troubles were sorted pretty quickly. Last one i noticed on mine was when you were checking L and R temp control on Hevac the reaction was transposed. Left button moved right select and right button moved right select. Other than that not found a problem recently. But then again not used it much.
Similar threads
