Its broken.

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Even if it's down on a few cylinders, it will still run. It's a solid lump.
Unplug a couple of plug leads and it might grumble a bit but will still fire up and run
 
LetsHopeItFits said:
The coils? As in the ignition coil?
Or do you mean the connector to the fuel injectors? They didnt do anything last time I checked...
Click to expand...
I really am dying to see the result of all this.
The point of doing it with the engine warmed up is so that all metals will have expanded to take up the running clearances and give a true reading.
The point of taking all the plugs out is two fold, one is that you can then do the job faster so the engine stays warm, and two, the starter motor doesn't have to work to compress air etc in the cylinders, except the one you are testing.
In each case keep the engine turning over until the reading stabilises before recording it and then moving on.
And only do the wet reading after the dry one.

Looking forward to the table of results!
 
Stanleysteamer said:
I really am dying to see the result of all this.
The point of doing it with the engine warmed up is so that all metals will have expanded to take up the running clearances and give a true reading.
The point of taking all the plugs out is two fold, one is that you can then do the job faster so the engine stays warm, and two, the starter motor doesn't have to work to compress air etc in the cylinders, except the one you are testing.
In each case keep the engine turning over until the reading stabilises before recording it and then moving on.
And only do the wet reading after the dry one.

Looking forward to the table of results!
Click to expand...
Not sure if theres a way Im supposed to warm the engine up, given its not running. Perhaps giving it a hot water bottle?
Relistically the engine isnt going to be at or above 10°C until spring/summer (unless it runs of course), so its a cold winter test or no test at all.
 
LetsHopeItFits said:
Not sure if theres a way Im supposed to warm the engine up, given its not running. Perhaps giving it a hot water bottle?
Relistically the engine isnt going to be at or above 10°C until spring/summer (unless it runs of course), so its a cold winter test or no test at all.
Click to expand...
Forgive me for my idealistic comment.
I had a feeling that was the case.
This thread has been running so long that I have forgotten some details.
 
LetsHopeItFits said:
Not sure if theres a way Im supposed to warm the engine up, given its not running. Perhaps giving it a hot water bottle?
Relistically the engine isnt going to be at or above 10°C until spring/summer (unless it runs of course), so its a cold winter test or no test at all.
Click to expand...

Don't worry about it.
Just do the test dry then wet and post results.
Then we can all move on to the next step knowing its fine :) .

Stick with the plan dont get sidetracked.

J
 
Still not looked at them - still not sold them.
If I fix it and kept it long term, is there a more reliable system I can fit than the current EFI system? I cant fit carbs, because its a 1996, so it needs catalytic converters, and cats dont like carbs (No idea why Garfield ate lasagna). If theres a good alternative, I might just jump straight for that instead of faffing around (after a compression test, obviously!)
Or am I better of just selling it and getting a 300tdi? Ive driven both a 300tdi and a 200tdi and compared to the V8 they felt like crap, much less responsive, much slower/less powerful, but compared to a broken V8, theyre infinately better. And by the sounds of it, a tdi would actually have running costs that make it sensible to drive to places in...
For me, the facelift discovery 1 is peak land rover - more practical and roomy than a range rover, more comfortable and less likely to be nicked than a defender, although the longer wheelbase and higher payload of a 110 would be fantastic.
 
MJI said:
Megasquirt is an option, an aftermarket injection system.


Non D1 engine is another option, IF you want to lose the V8 and go Diesel
www.broadlanelandrovers.co.uk

Broad Lane Land Rovers Ltd

Broad Lane Land Rovers Ltd
www.broadlanelandrovers.co.uk www.broadlanelandrovers.co.uk
Click to expand...
I'm not a fan of the TD5 if I'm honest...
And do MS have a significantly better reliability than the standard stuff? Possibly paired with electronic ignition?
marjon said:
You are bobbing all over the place again.

Compression test the engine, go from there.

J
Click to expand...
Yes, sitting inside next to the fire and typing into a laptop is much easier than going down to the carpark where its sat and mucking about with it....
I might drag it up here and plonk it right infront of the window, as motivation to get on with it!
 
14CUX is very, VERY simple and actually generally reliable. Megasquirt is a very steep learning curve, as is any kind of engine conversion.

If you can't do the bare basics, getting halfway through something 1000X more complex and discovering as issue is going to mean the same situation, which much less available support and knowledge, as nobody will have an understanding of exactly how you've done it.
 
Last edited:
Mega squirt is good… but comes at a price.
(Ecu can be set to run on different grades of fuel)

Original set up is easy once you have it sorted. Only problem I had was ecu played up and over fuelled but soon noticed this and all good with new ecu
 
You must log in or register to reply here.

Similar threads

S
Chassis change out
Replies
4
Views
260
Stu@69
S
M
Advice on replacing both rear toe spindle links on Disco 4
2
Replies
29
Views
1K
Anaconda
A
loonyspoony
Disco 1 300TDI No Start
2 3
Replies
41
Views
2K
loonyspoony
loonyspoony
awkwardbob
L322 2003 L322 Can’t open bonnet -battery flat
Replies
16
Views
545
marjon
marjon
tweedandbriar
*** Injector Adjusters Stuck - Help Needed ***
2
Replies
28
Views
1K
Tim4x4
Tim4x4
Back
Top