- Posts
- 44,832
- Location
- East Dorset
I would just like to say
- Thread starter Hippo
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Hippo
Lord Hippo
- Posts
- 53,847
Funny looking sossij.
Stone56
Well-Known Member
- Posts
- 3,216
- Location
- Up a mountain
Inside view
- Posts
- 16,357
- Location
- Benfleet, Essex
...that I am "unwell". 
Very little sleep last night because of "hack-hack-hack" coughing.
Throat is so sore I cannot swallow my own spit without thinking "ouch that hurts".
Nose is running (not snot, just water).
Feel like the very devil. Arghhhhhhhhhh!
Very little sleep last night because of "hack-hack-hack" coughing.
Throat is so sore I cannot swallow my own spit without thinking "ouch that hurts".
Nose is running (not snot, just water).
Feel like the very devil. Arghhhhhhhhhh!
- Posts
- 68,233
- Location
- The Wooly Witch
...that I am "unwell".
Very little sleep last night because of "hack-hack-hack" coughing.
Throat is so sore I cannot swallow my own spit without thinking "ouch that hurts".
Nose is running (not snot, just water).
Feel like the very devil. Arghhhhhhhhhh!
That sounds like what I has ... jeez it hurts
- Posts
- 16,357
- Location
- Benfleet, Essex
Tell him the ceiling (above) said get a move on!Well, plasterer been and gone, skimmed over hollow sounding areas above switches so I hope it doesn't come away, not done ceiling or rough walls with loose plaster on, say's I'll have to wait on a decision from above
- Posts
- 7,877
- Location
- East Midlands
Well, plasterer been and gone, skimmed over hollow sounding areas above switches so I hope it doesn't come away, not done ceiling or rough walls with loose plaster on, say's I'll have to wait on a decision from above
Looks like some progress then. I can't quite work it out from the pictures - has enough been done that you can re-mount the radiator?
Tell him the ceiling (above) said get a move on!
It's finished according to plastereerComing Thursday pm to put skirting boards back
No mention of re fitting radiator yet
Stone56
Well-Known Member
- Posts
- 3,216
- Location
- Up a mountain
You normally do the ceiling first du to the scrim round the edges that he has not used to stop crackingWell, plasterer been and gone, skimmed over hollow sounding areas above switches so I hope it doesn't come away, not done ceiling or rough walls with loose plaster on, say's I'll have to wait on a decision from above
- Posts
- 7,877
- Location
- East Midlands
..that the LATHE has landed.
Snowing here!
Now I need to work out how to get it working.
3 very nice gentlemen have just delivered the lathe I bought on e-Bay.
It is a little Boxford AUD (Serial Number 12161 and it appears (to my eyes anyway)to be in pretty good nick.
The ways are sound and unmarked, the slides are all silky-smooth and with no discernable backlash.
It came with:
An engineers surface plate- goodness that's heavy.
A full set of cutting tools (mostly unused).
A set of 24 collets and two collet arbors, but no drawbar.
A set of 4 tool posts and tool-holders of different style/flavours.
A micrometer carriage stop.
A standard carriage stop.
The backplate on there has an index (72 position) and an index pin mounted on the headstock. Don't think that was standard?
There is a backplate for clamping items to as well, and a drive dog.
@fizzy on the mig forum gave me some good advice on how to move it, but in the end the seller popped up and said "my mates in the moving business" and for £150 they brought it here and I didn't need to lift a finger.
I will give it a clean and lube and sort out a VFD (3-phase). Really pleased I am.
UPDATE:
I just took another look at it, and....
In the centre section of the cabinet I found:
A Pratt-Burnerd 4-Jaw Chuck
A fixed Steady.
A travelling steady.
The draw bar for the collet set.
Stone me, I think the 2 chucks are worth as much as I paid for the whole shebang. PMSL
Looks like a nice, workmanlike bit of kit. Good to see you've got it under cover too and they didn't just leave it in the garden under a tarp. You've done quite well for accessories too - I can see extra chuck jaws and a few other items knocking about. Is that the index plate I can see behind the chuck?
You'll find the lathe has as much of a medicinal effect for your respiratory ailment as anything you get from a doctor.
That's what I thought he would do but it's hard work getting them to do anything
Hippo
Lord Hippo
- Posts
- 53,847
Fink jesus was a wood butcher. Not sure if he did plasterering.Well, plasterer been and gone, skimmed over hollow sounding areas above switches so I hope it doesn't come away, not done ceiling or rough walls with loose plaster on, say's I'll have to wait on a decision from above
- Posts
- 44,832
- Location
- East Dorset
His Dad was a wood butcher, fink he was a preecherman!!! Dunno if he ever had a proper job!
Well maybe he did!
Blog | Angel Studios
Discover the latest news from Angel Studios. Catch up on what's happening with your favorite shows and movies like The Chosen, The Wingfeather Saga and more.
Stone56
Well-Known Member
- Posts
- 3,216
- Location
- Up a mountain
Carpenter's Labour then ? Happened that long a go no one will ever knowHis Dad was a wood butcher, fink he was a preecherman!!! Dunno if he ever had a proper job!
Well maybe he did!
Blog | Angel Studios
Discover the latest news from Angel Studios. Catch up on what's happening with your favorite shows and movies like The Chosen, The Wingfeather Saga and more.www.angel.com
- Posts
- 16,357
- Location
- Benfleet, Essex
Yes, the 72-point (why that number?) is behind the chuck. I reckon it will be because 72 is a magic number divisible by all too many other numbers. 72/36/24/18/9/8/6/4/2/1. Just like why the Old UK pound was best @ 240 Pence.
- Posts
- 44,832
- Location
- East Dorset
....that Britney Ferries, after my request to upgrade my email to a complaint, have decided to become all reasonable.
So I should now be getting what I thought I had booked.
Result!!
So I should now be getting what I thought I had booked.
Result!!
- Posts
- 44,832
- Location
- East Dorset
Maybe, but maybe not...
" For Jesus, carpenter work may have been more about working with limestone rather than timber. And, if we expand the definition further to include all-purpose craftsmen, then we may be looking at an occupation that is similar to a modern handyman, skilled in a variety of building and repair work."
But in Aramaic, "The term carpenter may correspond with the Aramaic word ‘naggar,’ meaning ‘a learned man.’"
As you say, so long ago, who gives a monkey's?
Similar threads
