I would just like to say

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
I have been freezing my nethers off in my little workshop.
It is tedious making ring-plates 42mm ID 62mm OD out of 3mm sheet steel on a lathe.
Lots of operations for very little progress, but we got there. :D

This is the result below. A Two Wheel Drive (2WD) unit for a pedal car racer. Itcan have any 10Spd cassette mounted to it and it is compact and pretty lightweight. Those are all the main parts all stacked together and held there by gravity. Some bits get welded together (bottom 3 elements) but the top 2 are bolted to the rest with small M5 bolts locking the upper and lower rings together and fitting in between the teeth of the sprocket you can just see sandwiched between the 2 ring-plates.
I am pleased with how it has come out. :)
View attachment 330552
Looking good Dan.
 
Well the fog light went in, and the reversing light on the other side too as well as replacing the rather dark indicator bulb.....
BUT!!!!

(You knew this was going to happen didn't you, seems to be my month, or is it the year, for this?)

As I was removing the offside cluster, the clear perspex screen that covers it, and had been hanging on by its fingernails, as I discovered at MOT time, came "detached". Luckily it didn't break or fall.

Nowt forrit but to take it indoors and clean it throughly prior to some fiddly work with sellotape. Hain't got no proper waterproof tape, that will have to wait until I can get some.
I will research what to stick it back together with. 2 pack expoxy I expect. It is obvious that Citroen's own glue ain't all that brill.

And when I did the nearside I noted it had started to part company too so did a "stich in time" operation on that one too.

I may have been a little hasty about how I thought Citroen had designed all bulb holders to be specific. I looked more closely at the ones on the nearside and came to the conclusion they were all the same. Haven't checked back on the offside as not really that bovvad and CBA to detach the gas ram, take out the starbolts etc etc.

4th day without CH. Getting used to it but it isn't funny any more. Wondering what a 2kw electric fan/convector heater on pretty much 15 hours a day, is costing? Answer 22.35 p/Kw/hr will be our new rate, the old rate must be more :eek: Which it is so about £4 a day. Well that would be on full time and full power, which it isn't but it makes you think.:(
My "Smart Meter" Actually works and I am tracking it in a daily spreadsheet . Castle clarke is burning £10..12/day on energy.
A pretty consistent 16Kwh on trickery and the rest on Gas. It is pretty much a 50:50 split pricewise as gas is 25% the cost/Kwh of trickery. :)
 
I have been freezing my nethers off in my little workshop.
It is tedious making ring-plates 42mm ID 62mm OD out of 3mm sheet steel on a lathe.
Lots of operations for very little progress, but we got there. :D

This is the result below. A Two Wheel Drive (2WD) unit for a pedal car racer. Itcan have any 10Spd cassette mounted to it and it is compact and pretty lightweight. Those are all the main parts all stacked together and held there by gravity. Some bits get welded together (bottom 3 elements) but the top 2 are bolted to the rest with small M5 bolts locking the upper and lower rings together and fitting in between the teeth of the sprocket you can just see sandwiched between the 2 ring-plates.
I am pleased with how it has come out. :)
View attachment 330552
Looks a pro job to me well done👍
 
Clear CT1 is a good allrounder and a tad flexible good for mating different materials together do a search on it's specified use
Thanks for that, I'll google CT1 and see what it says.
I just wish I has some spare bits to practise with and see if it really does the job.
But it must be some sort of hard plastic to hard plastic.
Ta again, mate!:):):)
 
My "Smart Meter" Actually works and I am tracking it in a daily spreadsheet . Castle clarke is burning £10..12/day on energy.
A pretty consistent 16Kwh on trickery and the rest on Gas. It is pretty much a 50:50 split pricewise as gas is 25% the cost/Kwh of trickery. :)
I suppose I could buzz off out each day, move the wheelie bin and other rubbish, open the cabinet and take a reading!
Don't know if I can do it via the website. Octopus sure know!
At least we know that gas consumption is near zero!
Just had a quick look at what air-sourced heat pumps cost in 'lectric. ~Not funny! And W read me a bit off some news she found this morning saying that boiler companies are going to be penalised if they don't flog enough or the wretched HP things.
Grrrr!!
 
I have been freezing my nethers off in my little workshop.
It is tedious making ring-plates 42mm ID 62mm OD out of 3mm sheet steel on a lathe.
Lots of operations for very little progress, but we got there. :D

This is the result below. A Two Wheel Drive (2WD) unit for a pedal car racer. Itcan have any 10Spd cassette mounted to it and it is compact and pretty lightweight. Those are all the main parts all stacked together and held there by gravity. Some bits get welded together (bottom 3 elements) but the top 2 are bolted to the rest with small M5 bolts locking the upper and lower rings together and fitting in between the teeth of the sprocket you can just see sandwiched between the 2 ring-plates.
I am pleased with how it has come out. :)
View attachment 330552
Nice one! looks like a piece of modern art!!:):):)
 
My "Smart Meter" Actually works and I am tracking it in a daily spreadsheet . Castle clarke is burning £10..12/day on energy.
A pretty consistent 16Kwh on trickery and the rest on Gas. It is pretty much a 50:50 split pricewise as gas is 25% the cost/Kwh of trickery. :)
I've just checked and I can more or less check rdaily consumpetion via Octopus energy online. Funny how our gas consumption has dropped to zero!
not so funny re the electric tho!
 
Yup, I could hear rattling on the over run 50/60m mph it was just a matter of time, ive been meaning to take the serial numbers
off the gear/tranny boxes all week. :rolleyes:
Tis a shame you haven't got a known good'un lying around. I can see new tranny costing almost as much as wot you paid for it. Bit of a shame, sympathies Mate.:(
 
Back
Top