I would just like to say
- Thread starter Hippo
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Don’t ask me. I would just wear it the wrinkles (well most) can’t be seen and some disappear, well in my shirts that is
J
Steam
J
Hippo
Lord Hippo
- Posts
- 52,080
Ask yer dorris
- Posts
- 13,691
- Location
- The Principality
Put some padding on top of the MDF (a folded up thick bed sheet is good) and then iron your on top of that. A steam iron is best but if you don't have one then you could try dampening your sheet and then iron it - this should steam the creases out. I hate ironing!
Hippo
Lord Hippo
- Posts
- 52,080
Gorra steam iron. Never used it so will experiment.
As the former owner of a 110 and a td5( long wheel base) and now a series 2a, this doesn't just " strike a chord" it strikes too many to mentionFREELANDERS RULE.
My Freelander is the bestist and has:
Leffer heated comfortable seats.
Comfortable suspension.
Enough power to accelerate 0 to 60mph in 10 seconds.
Brakes that actually work. 67 to 0mph in 4 seconds.
Space for 4 passengers to travel in comfort.
Air conditioning (proper air con - not a hole in the bulkhead)
A heater that works.
Smooth auto gearbox with optional sport mode and manual shift.
Headlights that actually light up the road ahead.
No rust.
A radio you can hear.
4 wheel drive.
Electronic traction control.
ABS.
Hill Descent Control.
Electronic Brake force Distribution.
Boot space big enough to put in everything I need.
A diagnostic socket I can use to fault find it.
Electric windows and mirrors.
Roof bars so I can fit ma roof rack bars.
Go anywhere ability oft road.
Enough power to tow a caravan if I want to be a snail.
Can actually steer round corners and follow the road ahead.
Doesn't have any water leaks.
Looks smart and is presentable.
Doors that dun't fall oft.
Comfortable on long journeys.
It's got character anorl.
Up yours tratterers.
!!!¡¡¡
- Posts
- 66,663
- Location
- The Wooly Witch
Morning all
a bit dull t'day
rain forecast fer later
have a good un
a bit dull t'day
rain forecast fer later
have a good un
Stone56
Well-Known Member
- Posts
- 2,636
- Location
- Up a mountain
Check the fuel lines thay perishAnd no, it don't idle on half choke!
I cannot say I know all that much about 2 strokes. But this is the first time one has played me up.
Stone56
Well-Known Member
- Posts
- 2,636
- Location
- Up a mountain
- Posts
- 13,691
- Location
- The Principality
Sunny here but memories of what happened to it yesterday are very vivid so I won't hold my breath for the rest of the day.
- Posts
- 15,268
- Location
- Benfleet, Essex
Morning All.
Dull & Dismal today (but maybe that's just a reflection on me).
Have a great day!
Dull & Dismal today (but maybe that's just a reflection on me).
Have a great day!
- Posts
- 41,600
- Location
- East Dorset
This is one of the things I am doing.
I spent a few hours last night watching YouTubes on repairing strimmers that don't run very well.
One thing that is fun is that none of mine ever came with air filters. So it is a bit surprising that they work, or worked, as well as they did! So I'll be cutting up some old, foam, pan scrubs.
It's one of those things where I sort of thought it couldn't be right but was always too busy to do anything.Such a pain that adjusting the jets etc requires a "pacman" socket/screwdriver. With the older 4 stroke one I simply took a hacksaw to it and cut through the housing and the tops of the jets to give me a slot so I could use an ornery screwdriver. I may well do this with this one too.
A lot of peeps simply buy a new carb as it is almost as cheap as getting a rebuild kit, separate hose, fuel filters, the tool etc which if you shop carefully you can get with the carb. Even including the special tool.
It goes against the grain for me to do this, but I may well do.
All good fun and grateful for any advice, as usual!
- Posts
- 41,600
- Location
- East Dorset
No but you are right!Steam iron ?
Sorry should have went to the end of Fred
Or do like people did before steam irons became a "thing", either iron it slightly damp, or wet a cloth like an old tea towel and iron it through that.
I find that even with a steam iron you sometimes still need to do this.
Another tip is to get a spray gun/bottle thing like you use to spray kitchen cleaner or white disinfectant with and fill it with water, then you can spray whatever you are ironing with that and keep doing it until the creases eventually go.
(You can tell I didn't go straight from school to uni to marriage)!! And my ex never ironed my shirts properly, she did one, I told her I didn't like the way she ironed a deliberate crease across the yoke at the back so she told me to do it myself then.
I did, but she refused to iron any of my shirts ever again! (This was when she wasn't working, she didn't get a proper full time job for the first 3 or 4 years.)
(How that marriage lasted 7 years I'll never know!)
- Posts
- 41,600
- Location
- East Dorset
So after yesterday's sunny weather, today it is drizzly and has rained all night.
It is supposed to stop by lunchtime.
Off to town this arvo for some shopping and to show the vet the dog's teef.
Have a good day folks!
It is supposed to stop by lunchtime.
Off to town this arvo for some shopping and to show the vet the dog's teef.
Have a good day folks!
saxavordian
Well-Known Member
- Posts
- 8,556
When our illuminated illustrious leader spoke(peace be upon him).
I was inspired by his thoughts on actual real women with proper anatomy in regards to driving Landrovers.
As a genuine parts real men not third party prosthetic added. We should thank these women who toil the muddy land as we sit behind steering wheel removing said chariot of burden.
- Posts
- 66,663
- Location
- The Wooly Witch
Is yer nap going along the lenff of the table or across the widff ?
Similar threads
