- Posts
- 16,552
- Location
- Benfleet, Essex
67 times for me so far...long may it (and I) continue.It's been happening like that for the last 56 years that I have experienced....... one day it won't though
I would just like to say
- Thread starter Hippo
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
- Posts
- 12,249
- Location
- Far out West
No eye dear
J
I think I must live in the dark ages
- Posts
- 9,112
- Location
- North Lincs
Don't worry, give it a couple of hundred years and you will be getting closer to us......I think I must live in the dark ages
- Posts
- 12,249
- Location
- Far out West
I think I might be a bit too old to notice by then
moved here from hazelmere years ago, but I don’t think I’ll go back
- Posts
- 16,552
- Location
- Benfleet, Essex
Have you never watched "Dexter"?What's it on and what's it about?
Not too savvy with this downloading it stuff
J
Go look it up on IMDB.com https://www.imdb.com/title/tt0773262/
Last edited:
- Posts
- 13,791
- Location
- The Principality
I was expecting the sight but not the sound. I roared with laughter.Nope that looked pretty straight through, maybe had a special spreader attachment
J
- Posts
- 45,158
- Location
- East Dorset
Morning, afternoon and evening all!
God it's been Issingdown here all day.
So boring we never did much at all.
BUT the postman brought me my drive belt for my head unit so I'll be playing with that soon.
Fecking Oakfartnitureland are saying that Paypal won't accept the payment, (prolly as it's been so long since we paid for the fecking thing) so they are asking that we send them all sorts of personal info, photocopy of passport etc etc before they'll make payment via bacs.
No chance. So I'll ring em on Monday and tell them to send a cheque or pay back via the credit card, or we'll just let the credit card company deal with them.
After all, when they took our money back in April we didn't ask them for their mother's maiden name and their inside leg measurement.
Sorry about your dottir @My Old Landy .
Hope she recovers soon and completely.
God it's been Issingdown here all day.
So boring we never did much at all.
BUT the postman brought me my drive belt for my head unit so I'll be playing with that soon.
Fecking Oakfartnitureland are saying that Paypal won't accept the payment, (prolly as it's been so long since we paid for the fecking thing) so they are asking that we send them all sorts of personal info, photocopy of passport etc etc before they'll make payment via bacs.
No chance. So I'll ring em on Monday and tell them to send a cheque or pay back via the credit card, or we'll just let the credit card company deal with them.
After all, when they took our money back in April we didn't ask them for their mother's maiden name and their inside leg measurement.
Sorry about your dottir @My Old Landy .
Hope she recovers soon and completely.
- Posts
- 16,552
- Location
- Benfleet, Essex
... that lathe boy strikes again.
The requirement (of a friend of mine for M10 threaded nuts with 19mm AF instead of 17mm as standard means you have to make your own.
It is just some 19mm Hex-bar and 4 or 5 hours of messing about (aka "FUN") on a mini-lathe.
While it was perishing cold in my little workshop I enjoyed making these as it is something that I have never done before.
Sequence was:
The requirement (of a friend of mine for M10 threaded nuts with 19mm AF instead of 17mm as standard means you have to make your own.
It is just some 19mm Hex-bar and 4 or 5 hours of messing about (aka "FUN") on a mini-lathe.
While it was perishing cold in my little workshop I enjoyed making these as it is something that I have never done before.
Sequence was:
- Swap out the 4-jaw chuck for the 3-jaw chuck.
- Cut Hex bar into 4 smaller manageable lengths.
- Progressively drill each piece 4mm, then 6mm, then 8.5mm.
- Start an M10 thread in each piece and finish by hand with a tap-wrench (too grunty for a little mini-lathe to do).
- Cut the tapped sections into 2 or 3 pieces that are just over the size (height) of standard M12 nuts with an angle-grinder (mini-lathes do not like parting-off operations).
- Mount each piece int othe chuck and face off and chamfer each end and chamfer the threaded holes.
... that lathe boy strikes again.
The requirement (of a friend of mine for M10 threaded nuts with 19mm AF instead of 17mm as standard means you have to make your own.
It is just some 19mm Hex-bar and 4 or 5 hours of messing about (aka "FUN") on a mini-lathe.
While it was perishing cold in my little workshop I enjoyed making these as it is something that I have never done before.
Sequence was:
I have never done this before, but they came out pretty good and they fit very well onto M10 stud (even though I say so myself).
- Swap out the 4-jaw chuck for the 3-jaw chuck.
- Cut Hex bar into 4 smaller manageable lengths.
- Progressively drill each piece 4mm, then 6mm, then 8.5mm.
- Start an M10 thread in each piece and finish by hand with a tap-wrench (too grunty for a little mini-lathe to do).
- Cut the tapped sections into 2 or 3 pieces that are just over the size (height) of standard M12 nuts with an angle-grinder (mini-lathes do not like parting-off operations).
- Mount each piece int othe chuck and face off and chamfer each end and chamfer the threaded holes.
You will be buying a bigger shed and lathe soon
.J
- Posts
- 45,158
- Location
- East Dorset
Look good to me!... that lathe boy strikes again.
The requirement (of a friend of mine for M10 threaded nuts with 19mm AF instead of 17mm as standard means you have to make your own.
It is just some 19mm Hex-bar and 4 or 5 hours of messing about (aka "FUN") on a mini-lathe.
While it was perishing cold in my little workshop I enjoyed making these as it is something that I have never done before.
Sequence was:
I have never done this before, but they came out pretty good and they fit very well onto M10 stud (even though I say so myself).
- Swap out the 4-jaw chuck for the 3-jaw chuck.
- Cut Hex bar into 4 smaller manageable lengths.
- Progressively drill each piece 4mm, then 6mm, then 8.5mm.
- Start an M10 thread in each piece and finish by hand with a tap-wrench (too grunty for a little mini-lathe to do).
- Cut the tapped sections into 2 or 3 pieces that are just over the size (height) of standard M12 nuts with an angle-grinder (mini-lathes do not like parting-off operations).
- Mount each piece int othe chuck and face off and chamfer each end and chamfer the threaded holes.
- Posts
- 23,123
- Location
- In the next Glen
- Posts
- 23,123
- Location
- In the next Glen
Tis very rare I would watch a vid over 20 mins on nootube.
- Posts
- 23,123
- Location
- In the next Glen
Morning all, I am on my own this weekend. My middle daughter got knocked over on a Zebra crossing on Thursday. She is not seriously hurt thankfully but the Mrs is going down to see her while I stay and look after the dog.
I am going to be servicing the 90 and replacing the water pump that threw its bearing before Christmas
Have a great weekend everyone!
Mega claim my mate got 50k for getting a astra wiper blade imprinted on his ugly mush.
I hope she's ok.
- Posts
- 9,112
- Location
- North Lincs
Morning, quite pleasant out. Have a great day
- Posts
- 13,791
- Location
- The Principality
Wet, so what's new.
I have to move the 'rubbish' out of the car today 'cos it's an early start tomorrow (6am) to take the car for its service.
Enjoy your Sunday, folks.
I have to move the 'rubbish' out of the car today 'cos it's an early start tomorrow (6am) to take the car for its service.
Enjoy your Sunday, folks.
What a pr1ck.... name and shame... I thought he was trying to get by at first which is still a selfish thing to do but then he goes closer and closer and closer....
Shocking video shows moment irresponsible runner causes stampede of 100 seals on the Yorkshire coast | Yorkshire Post
Similar threads
