Hicap phill
Well-Known Member
- Posts
- 16,209
- Location
- Wiltshire
Don’t worry I’m in a queue.I am on a bloody course
I would just like to say
- Thread starter Hippo
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
- Posts
- 16,320
- Location
- Benfleet, Essex
Barmy as in MAD, or Balmy as in "Warm"?
- Posts
- 16,320
- Location
- Benfleet, Essex
I managed to sneak off to my little workshop this afternoon.
Some playing with the sparkle-stick and the lathe resulted in some progress on her weathervane.
Some playing with the sparkle-stick and the lathe resulted in some progress on her weathervane.
Hicap phill
Well-Known Member
- Posts
- 16,209
- Location
- Wiltshire
Both.Barmy as in MAD, or Balmy as in "Warm"?
I’m not getting pulled into english lessons
- Posts
- 16,320
- Location
- Benfleet, Essex
Sorry, was not my place to pull you up. Apologies.Both.
I’m not getting pulled into english lessons
Hicap phill
Well-Known Member
- Posts
- 16,209
- Location
- Wiltshire
Tis ok. No need to apologise we are all happy pips in hereSorry, was not my place to pull you up. Apologies.
- Posts
- 8,986
- Location
- Solent
doriz
Well-Known Member
- Posts
- 17,312
Right e o, managed to fork over my borders and point up beneath the pan tiles prior to refitting the gutter. That’s tomorrow’s job
- Posts
- 6,580
- Location
- uk
Managed to get the terrace paving underway, was raining this morning but got out there late this afternoon to get a couple of slabs down.
- Posts
- 9,087
- Location
- North Lincs
I'm getting a bit excited, the mill I agreed to purchase with the money from my motorcycle sale is finally on a pallet and on it's way! It's only been 3 months
- Posts
- 13,784
- Location
- The Principality
Like thatI managed to sneak off to my little workshop this afternoon.
Some playing with the sparkle-stick and the lathe resulted in some progress on her weathervane.
View attachment 231566
It’s all a bit mad max! Instead of trying to weld the bottom section in upside down and horribly I made a u section that plates over my fresh side wall. Extra strength and spans over the verticals too which can’t be a bad thing. It’s a nice fit. Will melt it on soon!
Hicap phill
Well-Known Member
- Posts
- 16,209
- Location
- Wiltshire
Good evening from Scotland.
Trying to head south for a few days off but traffic/work/people/queues are not helping.
Trying to head south for a few days off but traffic/work/people/queues are not helping.
- Posts
- 12,075
- Location
- Far out West
Shimsteriom
Master Procrastinator
- Posts
- 41,905
- Location
- Over Here
Heavnin' All.
Well that was boring... but it pays a wage.
The funny thing is that now I've got a job one of the companies I've applied to previously have decided that they'd like to interview me. It's in IT again but at a much lower level so although the pay would be lower than my previous IT position, it would be several grand higher than the job I started today and I'm fairly sure it would be an easy job. I've already spoken to me new boss today and asked him for Thursday morning off so I can attend the interview and he's OK with it (not that he had a choice!)
One good outcome from todays boring warehouse work was that I got to do a delivery job later this afternoon which I quite enjoyed which re-affirms my desire to do driving for a living.
Well that was boring...
but it pays a wage. The funny thing is that now I've got a job one of the companies I've applied to previously have decided that they'd like to interview me. It's in IT again but at a much lower level so although the pay would be lower than my previous IT position, it would be several grand higher than the job I started today and I'm fairly sure it would be an easy job. I've already spoken to me new boss today and asked him for Thursday morning off so I can attend the interview and he's OK with it (not that he had a choice!)
One good outcome from todays boring warehouse work was that I got to do a delivery job later this afternoon which I quite enjoyed which re-affirms my desire to do driving for a living.
- Posts
- 44,734
- Location
- East Dorset
You can buy screws which are cross cut and can only be done up, not undone.
I'll see if I can find a link.
https://www.westfieldfasteners.co.u...MI887emaP-7gIVwbTtCh3z1gtLEAYYAyABEgKXa_D_BwE
Not brill but betterer than nuffink,
Your method sounds quite good.
Similar threads
