Hertfordshire Lanes?????
- Thread starter 99claydond
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
I'm going to buy some strengthened ones from Crown Diffs.
- Posts
- 83,266
- Location
- Embasinga stocæ
jai_landrover
Well-Known Member
- Posts
- 13,392
- Location
- Luton
Last thing you want is broken bits flying around your nice new diff took me ages to remove my fragments from my britpart shaft episode at a punch event at a quarry up nr Northampton.
Booger
New Member
- Posts
- 1,778
- Location
- Dorsetshire
What goes on tour, stays on tour.
That's exactly what I say when I have been on tour and pulled a minger
jai_landrover
Well-Known Member
- Posts
- 13,392
- Location
- Luton
First time I've seen them. Not cheap £650 plus they are I think from the website clutch plate design which eventually do wear out or need re shimming. Detroit is a propper locker and locks fully and cheaper fit and forget. Kaiser would be my next one to buy they seem good and ashcroft sell them 5 mins up the road.
- Posts
- 83,266
- Location
- Embasinga stocæ
dont they need air as well?
jai_landrover
Well-Known Member
- Posts
- 13,392
- Location
- Luton
I mean £850 looking at it again. Good find never seen it before but not cheap
- Posts
- 83,266
- Location
- Embasinga stocæ
Fur Trapper
Banned
- Posts
- 8,481
- Location
- international
jai_landrover
Well-Known Member
- Posts
- 13,392
- Location
- Luton
Looks to me like there is a small ammount of preload on the set of shims 6 and 7 friction between them as 6 is driven directly by carrier or cage as they call it and 7 is directly connected to 10 side gear which is your half shaft wheel. When the cross shafts rotates under power against the power ramp angle it forces 8 planet driver outward to exert more friction and tighten up and drive that driveshaft.
Last edited:
jai_landrover
Well-Known Member
- Posts
- 13,392
- Location
- Luton
- Posts
- 83,266
- Location
- Embasinga stocæ
he is the guy that services my '40
jai_landrover
Well-Known Member
- Posts
- 13,392
- Location
- Luton
Ok saying its a clutch design is wrong it has no actual clutch material its correct term is plate type.
Good write up here:
Into The Red - Limited Slip Differential
Good write up here:
Into The Red - Limited Slip Differential
jai_landrover
Well-Known Member
- Posts
- 13,392
- Location
- Luton
edited:
Looks to me like there is a small ammount of preload on the set of shims 6 and 7 friction between them as 6 is driven directly by carrier or cage as they call it and 7 is directly connected to 10 side gear which is your half shaft wheel. When the cross shafts rotates under power against the power ramp angle it forces 8 planet driver outward to exert more friction and tighten up and drive that driveshaft.
Looks to me like there is a small ammount of preload on the set of shims 6 and 7 friction between them as 6 is driven directly by carrier or cage as they call it and 7 is directly connected to 10 side gear which is your half shaft wheel. When the cross shafts rotates under power against the power ramp angle it forces 8 planet driver outward to exert more friction and tighten up and drive that driveshaft.
sible88
New Member
- Posts
- 3,492
- Location
- Hertfordshire
Had a good day at Whaddon today!!
Really liked it as you could make your own track!
Really liked it as you could make your own track!
Ryder
Having a senior moment
- Posts
- 6,616
- Location
- West Bedforshire
Are we ooking to return this conversatio to english in the near future?
Booger
New Member
- Posts
- 1,778
- Location
- Dorsetshire
My thoughts exactly, the only thing I understood in the last 5 pages was that MHM has a 40" wiener, and he gets it serviced by a dude
- Posts
- 83,266
- Location
- Embasinga stocæ
my GT40, ya fool 
