PRO
Well-Known Member
- Posts
- 648
- Location
- West Yorkshire
Again, dcs. Sounds like front bcm is kapput.
Everything JLR SDD related (feel free to add experiences/help).
- Thread starter Nodge68
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
- Posts
- 34,868
- Location
- North Shropshire
sorry, dcs?
PRO
Well-Known Member
- Posts
- 648
- Location
- West Yorkshire
DTCs always check those before anything
- Posts
- 34,868
- Location
- North Shropshire
i've never managed to pull any DTC when the ignition is off, including BCM, it just says its not responding
- Posts
- 34,868
- Location
- North Shropshire
before i managed to wipe the keys and i could turn the ignition on in the emergency location, there werent any DTC related to BCM
PRO
Well-Known Member
- Posts
- 648
- Location
- West Yorkshire
There's your issue. BCM/KVM should respond with ignition off.
- Posts
- 34,868
- Location
- North Shropshire
my mistake, it does respond. 3 codes;
P0801-11 intermittent, reverse inhibit control circuit malfunction
B1B01-55 intermittent, Key transponder
causes - not configured
B100D-87 intermittent, Column lock authorisation
causes - missing message
batt volts too low
CAN network fault
no response from steering column lock module, instrument cluster, central junction box
steering column lock fault
batt volts, unlikely with new battery and its been kept on charge
CAN network fault possible
steering column lock fault, it unlocks when SDD cycles the ignition, so unlikely?
P0801-11 intermittent, reverse inhibit control circuit malfunction
B1B01-55 intermittent, Key transponder
causes - not configured
B100D-87 intermittent, Column lock authorisation
causes - missing message
batt volts too low
CAN network fault
no response from steering column lock module, instrument cluster, central junction box
steering column lock fault
batt volts, unlikely with new battery and its been kept on charge
CAN network fault possible
steering column lock fault, it unlocks when SDD cycles the ignition, so unlikely?
- Posts
- 34,868
- Location
- North Shropshire
i think there can't be a can bus problem if BCM and KVM both have green ticks? i think they are bogus
PRO
Well-Known Member
- Posts
- 648
- Location
- West Yorkshire
Do a network integrity test I bet the bcm is reporting some porkies
- Posts
- 34,868
- Location
- North Shropshire
ok did that, it seemed to talk to the BCM but i dont know what much of the values meant.
when i went back to DTC screen there were 4 events;
B10A9-00 RFA J_14229_DTC_B10A9 (intermittent)
- key fobs need reprogramming (i know this bit) (intermittent)
U0140-00 ACM, DDM, PDM lost communication with body control module (intermittent)
i've always had DTC for door modules (door locks) but never had an issue with them
when i went back to DTC screen there were 4 events;
B10A9-00 RFA J_14229_DTC_B10A9 (intermittent)
- key fobs need reprogramming (i know this bit) (intermittent)
U0140-00 ACM, DDM, PDM lost communication with body control module (intermittent)
i've always had DTC for door modules (door locks) but never had an issue with them
- Posts
- 34,868
- Location
- North Shropshire
What sort of porkies do you think it might be telling?
PRO
Well-Known Member
- Posts
- 648
- Location
- West Yorkshire
Something like g5ET£"E£TH6E"£JET67@'cdw
- Posts
- 34,868
- Location
- North Shropshire
Everything that got returned from bcm looked ok.. some was obviously raw/hex values.. but i think that would be normal
PRO
Well-Known Member
- Posts
- 648
- Location
- West Yorkshire
yeah drop me a pm will take this on whatsapp not sure when I can have a look as well.
- Posts
- 34,868
- Location
- North Shropshire
PM dropped, cheers
- Posts
- 34,868
- Location
- North Shropshire
I know we talked about getting the right part number for the fusebox/bcm but i've just seen one on ebay <£100
all the 2010-12 4.4tdv8 ones seem to have the same part number
tempted.. the mileage on the 2nd one is lower than mine
all the 2010-12 4.4tdv8 ones seem to have the same part number
tempted.. the mileage on the 2nd one is lower than mine
Range Rover L322 Fuse Box 4.4 TDV8 BH42-14F041-AA Under Dash 2010 to 2013 | eBay
<p dir="ltr" style="margin-top:0; margin-bottom:0;">Fuse box bcm for l322 facelift 2009-2012 4.4 tdv8.</p> <p dir="ltr" style="margin-top:0; margin-bottom:0;">In good used condition.</p> <p dir="ltr" style="margin-top:0; margin-bottom:0;">This item will need coding in if putting in a different...
www.ebay.co.uk
Hi i have a question about how complete a ABS brake bleed with the JLR SDD tool on my 2010 Freelander 2? As i am going to be replacing my ABS module. I have spent a good few hours in the software trying to find it but no luck dose anyone know where it is located or what it is called in the SDD software. The closest i think i have gotten is the brake system menu under complete vehicle data logger but there was nothing under that which suggests a ABS bleed or to activate the pump. Thank you. Im running SDD 165.00
Last edited:
