Henry_b
Think outside, no box required.
- Posts
- 15,506
- Location
- somewhere else
Ha i see what ya did there..So is the diesel if you know what you are doing.
You have to be clever to keep fixing it
P38A Diesel Head Removal - Flywheel Pin / Camshaft Locking Plate
- Thread starter TwoAndAQuarter
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
You have to be clever to keep fixing it
- Posts
- 58,170
- Location
- Preston Lancs.
Ha i see what ya did there..
You have to be clever to keep fixing it
No not really, if you are clever you fix something once maintain it and it stays fixed.
Henry_b
Think outside, no box required.
- Posts
- 15,506
- Location
- somewhere else
No not really, if you are clever you fix something once maintain it and it stays fixed.
The same can be said for the far superior V8
- Posts
- 58,170
- Location
- Preston Lancs.
The same can be said for the far superior V8
No i do not agree, the V8 requires far more maintenance than the diesel. Many more things to fail.
Henry_b
Think outside, no box required.
- Posts
- 15,506
- Location
- somewhere else
Lets agree to disagree
- Posts
- 58,170
- Location
- Preston Lancs.
Henry_b
Think outside, no box required.
- Posts
- 15,506
- Location
- somewhere else
- Posts
- 58,170
- Location
- Preston Lancs.
Henry_b
Think outside, no box required.
- Posts
- 15,506
- Location
- somewhere else
Datatek
Well-Known Member
- Posts
- 44,887
- Location
- Near Poitiers SW France
Except the diesels rarely go wrong.Ha i see what ya did there..
You have to be clever to keep fixing it
Henry_b
Think outside, no box required.
- Posts
- 15,506
- Location
- somewhere else
Apart from Op?
Datatek
Well-Known Member
- Posts
- 44,887
- Location
- Near Poitiers SW France
The liners will still go up and downThe same can be said for the far superior V8
Henry_b
Think outside, no box required.
- Posts
- 15,506
- Location
- somewhere else
Datatek
Well-Known Member
- Posts
- 44,887
- Location
- Near Poitiers SW France
Most if not all head failures can be traced back to repeated overheating which is down to failure to fix a problem like a duff viscous fan. The camshafts are made of steel on the M51 unlike the V8 where they seem to be made of cheese. No problems with ignition coils plugs or leads either and it's luck of the draw as to whether the liners will slip or not on the V8Apart from Op?
Henry_b
Think outside, no box required.
- Posts
- 15,506
- Location
- somewhere else
The V8 has a Flat tappet cam, the lack of ZDDP and the use of incorrect grade Oil will cause premature wear on any FT cam, not just the Rover V8
The Overheating is also what causes liners to drop, look after it and the thing should be ok
Datatek
Well-Known Member
- Posts
- 44,887
- Location
- Near Poitiers SW France
What about the cracked blocks?The V8 has a Flat tappet cam, the lack of ZDDP and the use of incorrect grade Oil will cause premature wear on any FT cam, not just the Rover V8
The Overheating is also what causes liners to drop, look after it and the thing should be ok
Henry_b
Think outside, no box required.
- Posts
- 15,506
- Location
- somewhere else
The Rover v8's casting in some cases was poor.
Which caused the water jackets to be "off centre" the thinner wall cracks when the block is cooked, the block shrinks away from the liner and thats it.
Depends on the engine, luck of the draw in some cases,
Human error as always, some blocks made it through though "coscast" blocks were the pinnacle of Rover V8's..
Datatek
Well-Known Member
- Posts
- 44,887
- Location
- Near Poitiers SW France
Funny, but the M51 doesn't suffer from those problems
- Posts
- 58,170
- Location
- Preston Lancs.
The V8 has a Flat tappet cam, the lack of ZDDP and the use of incorrect grade Oil will cause premature wear on any FT cam, not just the Rover V8
The Overheating is also what causes liners to drop, look after it and the thing should be ok
Bored out block with reduced wall thickness causes the liners to slip when it cracks. Have never see a 3.5 with slipped liners.
Henry_b
Think outside, no box required.
- Posts
- 15,506
- Location
- somewhere else
Funny, but the M51 doesn't suffer from those problems
I agree, all you have to put up with is..
Cracked heads
Timing chains
Injector(s)
No HP
No Torque
Only 6 cylinders etc
