UnitLandy
Well-Known Member
- Posts
- 228
- Location
- Whittonstall
Cheers! Took it out round the block and drives well. Although I've detected a new grating noise when turning the wheel. I'm I never done with this car?
P38 Diesel Injector Pump & Cam Top Dead Centre?
- Thread starter UnitLandy
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
UnitLandy
Well-Known Member
- Posts
- 228
- Location
- Whittonstall
Wrong threadbare what power steering fluid do I need. Haven't checked yet but I'll have a look in the reservoir.
Datatek
Well-Known Member
- Posts
- 46,517
- Location
- Near Poitiers SW France
ATF DEX 3
UnitLandy
Well-Known Member
- Posts
- 228
- Location
- Whittonstall
Steering fluid reservoirs good. So no need for any fluid. Still drips of diesel tracing from around the rear of the pump. I'll check that out Tomorrow.
RangeRoller dt
Well-Sprung Member
- Posts
- 14,854
- Location
- Trapped inside my head @ LZ asylum
If that’s as far as the adjustment will go do you know the state of the chains?
UnitLandy
Well-Known Member
- Posts
- 228
- Location
- Whittonstall
Actually looking at the picture I think there was slightly more room for adjustment. Think it was the high pressure lines stopping it's rotation any futher.
Datatek
Well-Known Member
- Posts
- 46,517
- Location
- Near Poitiers SW France
When turning the wheel or when the car is turning? If the latter, maybe a wheel bearing.
UnitLandy
Well-Known Member
- Posts
- 228
- Location
- Whittonstall
It's when turn the wheel. I pulled up on the drive and turned the wheel & heard the noise.
Datatek
Well-Known Member
- Posts
- 46,517
- Location
- Near Poitiers SW France
Column bearings or the little UJ at the end of the column maybe? Might be worth doing an oil change for the power steering.
UnitLandy
Well-Known Member
- Posts
- 228
- Location
- Whittonstall
Would something like that build up in noise or would the noise start suddenly? I don't remember it making this sound last time I drove it.
UnitLandy
Well-Known Member
- Posts
- 228
- Location
- Whittonstall
Just been listening to it while engine running. It's like a fast rattling noise from the front of the engine. It starts and after a while cuts off and then a starts again a few seconds later. It's definitely worse when I turn the wheels for some reason.
brianp38dse
Well-Known Member
- Posts
- 20,495
- Location
- heathrow
Check the drive belt and the roller guides.
UnitLandy
Well-Known Member
- Posts
- 228
- Location
- Whittonstall
Could be. I've got video of it but can't upload it. Just don't know why it's worse when turning the wheel.
It's had two new belts and the bearings sounded okay last time I checked. Wonder if they've just gone...
It's had two new belts and the bearings sounded okay last time I checked. Wonder if they've just gone...
UnitLandy
Well-Known Member
- Posts
- 228
- Location
- Whittonstall
Datatek, I've sent you an email with a link to the video I shot including the grinding sound on Dropbox.
Datatek
Well-Known Member
- Posts
- 46,517
- Location
- Near Poitiers SW France
UnitLandy
Well-Known Member
- Posts
- 228
- Location
- Whittonstall
Spot on! I'll get onto that. I'll do it when the radiator is being changed. It shouldn't be the pump as I've just replaced that. Likely the idler & tensioner pulley. Thanks lads!
Is it safe to drive or will I get done for noise pollution?
Is it safe to drive or will I get done for noise pollution?
- Posts
- 4,818
- Location
- Near Heathrow.
Upload the video to YouTube. Then copy the youtube link, and add here using the Insert Media.
UnitLandy
Well-Known Member
- Posts
- 228
- Location
- Whittonstall
Datatek
Well-Known Member
- Posts
- 46,517
- Location
- Near Poitiers SW France
Power steering pump not the water pump is what I was referring to.
UnitLandy
Well-Known Member
- Posts
- 228
- Location
- Whittonstall
How difficult us replacing that or does it come off easy enough?
