plastic soul
Active Member
- Posts
- 432
light guards please...how much?
Breaking Discovery 1 300Tdi ES
- Thread starter Brian S
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
- Posts
- 83,282
- Location
- Embasinga stocæ
engine temp sensor plug & cable loom?
Brian S
Well-Known Member
- Posts
- 2,886
- Location
- Braintree, Essex
Do you mean the window surround? I have a couple of those. Not sure how the seal pops out though.
Brian S
Well-Known Member
- Posts
- 2,886
- Location
- Braintree, Essex
The one on the thermostat housing? That should be there.
I am not sure it's got its own loom, might be part of the engine loom.
Do you mean you want a bit of the loom chopped off?
Brian S
Well-Known Member
- Posts
- 2,886
- Location
- Braintree, Essex
Have text you mate.
- Posts
- 83,282
- Location
- Embasinga stocæ
Nope - its about halfway down the cylinder head to the right (looking from the front) of the rocker cover. Sits in between the rocker cover and one of the heater pipes. It has a brown 2pin connector and the wires run along the hetaer pipe (or therabouts) to the front of the engine and back to the bulkhead. Mine have run too close to the exhaust and have embrittled and the insulation has fallen apart.
not sure how to describe it, when you put the window down, its the felt/ rubbery channel the window slides in? one side of mine is split and cracked so wind gets in!
i think its number 11 on here http://www.allbrit.de/UNI.cfm?PAGE=820706&SPRACHE=EN#
Last edited:
Brian S
Well-Known Member
- Posts
- 2,886
- Location
- Braintree, Essex
Have had a nightmare couple of days trying to fix my landy and currently say in a&e after my best mate got hit on the head by some heavy angle iron.
Been 36 hours up the unit and had no time to consider looking at parts.
Next up there Saturday.
Been 36 hours up the unit and had no time to consider looking at parts.
Next up there Saturday.
- Posts
- 83,282
- Location
- Embasinga stocæ
This is yours if you want it -
Landrover Discovery 300TDi Drivers door top frame (221332384345)
J.P.S
Active Member
- Posts
- 980
- Location
- Canterbury
Power steering pump??
i need to rubber seal as opposed to the frame, thanks though.
Brian S
Well-Known Member
- Posts
- 2,886
- Location
- Braintree, Essex
I have a brand new one I brought and never used, think I paid about £80 for it, I will let it go for £60 as I need the cash. Or the one on the engine I can do for £15
Brian S
Well-Known Member
- Posts
- 2,886
- Location
- Braintree, Essex
I have a couple of doors at home with the runners. Remind me what door again and I will check later.
Brian S
Well-Known Member
- Posts
- 2,886
- Location
- Braintree, Essex
Having a think about those. Was gonna put them on my new one but changed my mind as they looked a pain to fit, but I have rivnuts and bolts so gonna see if its easy enough.
I liked them on my old landy so would be good to have them back on.
Will let you know.
I have a couple of doors at home with the runners. Remind me what door again and I will check later.
drivers door fella, doesn't even need to be a full seal, its missing about 2 inches from the seal so whistles and blows when i'm driving haha!
mastersdave2
New Member
- Posts
- 86
- Location
- Birmingham
im sure there the same, on auto's and manuals, but i could be wrong so thought id ask anyway, im after a cylinder head for a 300tdi manual, ideally with pushrods and bolts?
discomark10
Well-Known Member
- Posts
- 3,977
- Location
- Milton Keynes
if you can solder, chop it put some heat shrink over it and solder it back up
Brian S
Well-Known Member
- Posts
- 2,886
- Location
- Braintree, Essex
They are the same. This one is good but I will be cleaning it up and having a light skim as they always need a bit.
The last couple I've done have sold for around £200
Similar threads
