- Posts
- 35,518
- Location
- North Shropshire
How long is this frigging bolt!?
What did you do with your Range Rover today
- Thread starter Dopey
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
- Posts
- 35,518
- Location
- North Shropshire
I'm properly stuck now.. the hard to get to bolt that holds the ball joint in place is knackered. I'm at a loss what to do 
Datatek
Well-Known Member
- Posts
- 45,585
- Location
- Near Poitiers SW France
I'ma hold off, been pointed out my fuel temp is way out, so gonna change that before I touch anything else, as the pump thinks the fuel is way colder than it should be.
- Posts
- 13,100
- Location
- Sud ouest France !
If the bolt won't come out as you expect you mave to..I'm properly stuck now.. the hard to get to bolt that holds the ball joint in place is knackered. I'm at a loss what to do
A, drop the fame,
B, cut the bolt after checking it can be put back in from the other side
Grrrrrr
Technician, Bodgit & Scarper Ltd
- Posts
- 19,648
- Location
- Buckinghamshire, UK. ('95 DT)
- Posts
- 35,518
- Location
- North Shropshire
Can't see how you'd cut it. but then you'd next need to drill and wind an extractor in. But you can't really get to it and it's not square onIf the bolt won't come out as you expect you mave to..
A, drop the fame,
B, cut the bolt after checking it can be put back in from the other side
I think I'm getting out of my depth on this one..
- Posts
- 13,100
- Location
- Sud ouest France !
Does the bolt move?
Get in there with a grinder or a reciprocating saw.
Pull the arm out completely and then renew the bits your focused on.
Get in there with a grinder or a reciprocating saw.
Pull the arm out completely and then renew the bits your focused on.
- Posts
- 13,100
- Location
- Sud ouest France !
Sorry I've misunderstood, what is exactly suck that long bolt or the ball joint nut?I'm properly stuck now.. the hard to get to bolt that holds the ball joint in place is knackered. I'm at a loss what to do
- Posts
- 35,518
- Location
- North Shropshire
One of the bolts that holds the ball joint in place
If you grind the head off then you'll never get the rest of the bolt out.. in my opinion.. but then i don't have the best imagination
Is the fuel quantity not low as a 90 year olds ball sack? Or is it likely to balance out a little after a new temp sensor?
- Posts
- 13,100
- Location
- Sud ouest France !
I don't suppose you've got a couple of pictures have you my good man. There may be some sacrifice to be had..
Datatek
Well-Known Member
- Posts
- 45,585
- Location
- Near Poitiers SW France
That is my understanding too, based on looking at RAVE the fuel temp sensor is under the top cover of the FIP and a new one is about £20 and looks an easy replacement.
- Posts
- 35,518
- Location
- North Shropshire
I don't suppose you've got a couple of pictures have you my good man. There may be some sacrifice to be had..
- Posts
- 6,447
- Location
- North Manchester
Don't remember having that problem when I did mine. If you raise the suspension does it give you enough clearance? Assuming it's part of the body that's in the way.
- Posts
- 35,518
- Location
- North Shropshire
It's underneath, bottom of the hub
- Posts
- 6,447
- Location
- North Manchester
ah that one. Bugger
- Posts
- 6,447
- Location
- North Manchester
I had better access
- Posts
- 35,518
- Location
- North Shropshire
Yes that one was easy, it's the other ones on the left of the pic
