- Posts
- 33,599
- Location
- North Shropshire
Yes but much reduced. I think it's more to do with holding the higher revs. It doesn't drop into neutral unless going very slow
L322 ZF8HP70 gearbox problem
- Thread starter kermit_rr
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
- Posts
- 33,599
- Location
- North Shropshire
I don't know if it's related but SDD is still not happy, complains the deployable side step isn't running.. well it's never had one!!
I also read somewhere about invalid ccf but can't remember where i saw that. It didn't say what was invalid
I also read somewhere about invalid ccf but can't remember where i saw that. It didn't say what was invalid
Then the torque converter is locking up OK, back to looking at speed and torque values - have you checked the output speed sensor is reading correctly?
- Posts
- 33,599
- Location
- North Shropshire
i havent, i'll plug SDD in tonight and have a look. presume its called something obvious
- Posts
- 33,599
- Location
- North Shropshire
What reading should i be looking for, how do i know if it's good or bad? And which speed sensor
Datatek
Well-Known Member
- Posts
- 44,883
- Location
- Near Poitiers SW France
As said, "output speed sensor". With live data and the car moving it should produce a signal but since I know feck all about the L322 diagnostics where it will appear and what it's called, I don't know.
- Posts
- 12,628
- Location
- Sud ouest France !
If you had clutch/torque slip you could have an input/output sensor correlation fault possibly? 
The speed sensor for the transmission output in rpm - not the wheel speed sensors or the composite road speed on CAN, an actual rpm value from the TCM, there is also a turbine speed sensor (Transmission input speed) also in the TCM, there are not that many PID's in the TCM so you should be able to identify them - you're looking for the readings to be plausible - i.e. output is >0rpm when the vehicle is being driven and smoothly increases/decreases, same goes for turbine speed but you don't need to be moving to read that one. I can't remember the correlation to engine rpm (it may be 1:1) but it'd be worth having that displayed along with the turbine speed to check for any anomalies in speed variation - also check in 'S'.
That would/should set a DTC, if the value is incorrect but still within the valid range, that'd give symptoms but no DTC.If you had clutch/torque slip you could have an input/output sensor correlation fault possibly?
- Posts
- 12,628
- Location
- Sud ouest France !
Very true, Clutch opening and shutting time limits.
There seems to be a trend of solenoid gauze blockages. Vw Audi has a gearbox setup that suffers from this type of issue.
There seems to be a trend of solenoid gauze blockages. Vw Audi has a gearbox setup that suffers from this type of issue.
Henry_b
Think outside, no box required.
- Posts
- 15,506
- Location
- somewhere else
Have you had the adaptions reset?
- Posts
- 33,599
- Location
- North Shropshire
I didn't see a live data selection called output speed sensor but saw a few others.
Transmission output shaft speed was interesting, it was at zero apart from a spike when starting and a spike when stopping.
There was transfer box motion sensor voltage which went from low to high, the switch happened before i came to a stop
Transmission output shaft speed was interesting, it was at zero apart from a spike when starting and a spike when stopping.
There was transfer box motion sensor voltage which went from low to high, the switch happened before i came to a stop
- Posts
- 33,599
- Location
- North Shropshire
It was supposed to have been done by the guy who did the oil change
Henry_b
Think outside, no box required.
- Posts
- 15,506
- Location
- somewhere else
8hp has a reputation for issues in the valvebody usually pressure leaks that can cause the trans to act erratically.
The priming valve in the valvebody losing fluid pressure is a favourite that can cause it to shift poorly.
The priming valve in the valvebody losing fluid pressure is a favourite that can cause it to shift poorly.
Datatek
Well-Known Member
- Posts
- 44,883
- Location
- Near Poitiers SW France
That does not sound right to me.
- Posts
- 33,599
- Location
- North Shropshire
In the higher gears, with high throttle inputs it seems fine, there would be greater leakage and bigger symptoms?
- Posts
- 33,599
- Location
- North Shropshire
That's what i thought
Datatek
Well-Known Member
- Posts
- 44,883
- Location
- Near Poitiers SW France
No signal to indicate that the output shaft is turning would certainly confuse the ECU.
Don't do that! The only time that should be done is if a software change requires it or solenoids have been replaced, doing so on a 'box that has had no work done can lead to some pretty bad shifts, some 'boxes never achieve their previously 'acceptable but could be better' shift behaviour.
