Wheel bearing play.

L

Landysi

New Member

Posts

38

Location

Kidderminster,Worcestershire

• Dec 26, 2010

• #1

Hi i am hoping you guys can help. I have a 1996 Defender 110. Have replaced all four bearings and races this year. However every time the play is adjusted out of the bearings within weeks it is back. Not only have i adjusted them up but it has also been to APB trading land rover specialist for adjustment but yet the play has stiil come back. Any ideas would be much appreciated

 

B

bmp42

Active Member

Posts

658

Location

Coimbra, Portugal

• Dec 26, 2010

• #2

what make of bearing where they? cos it sounds like the inner races are wearing

 

L

Landysi

New Member

Posts

38

Location

Kidderminster,Worcestershire

• Dec 26, 2010

• #3

I am not a 100% but think the boxes had all makes 4x4 on them.

 

Pikey

Dummy Ejection Facilitator..

Posts

47,185

Location

in Baron Wet Bum's Slave pit..

• Dec 26, 2010

• #4

Inner races shouldn't wear and certainly not in a week?? sounds far more likely that the nuts are loosening up in which case replace the hubnuts and locking washer and check the threads on the stub axle or better still just replace the stub axle, nuts and locking washer anyway.

 

B

bmp42

Active Member

Posts

658

Location

Coimbra, Portugal

• Dec 26, 2010

• #5

redhand said:

Inner races shouldn't wear and certainly not in a week?? sounds far more likely that the nuts are loosening up in which case replace the hubnuts and locking washer and check the threads on the stub axle or better still just replace the stub axle, nuts and locking washer anyway.

Click to expand...

have seen some Britpart ones go quicker than that down here - not fitted by me - Timken only for me, as far as adjustment goes they have been re adjusted by an Indy so they would have made sure that locknuts / tab washers would have been good to use. How did you pack the bearings with grease before fitting?

 

blue beasty

Leaks an prone to bits dropping off

Posts

63,117

Location

Gloucestercotshirewolds

• Dec 26, 2010

• #6

never a good idea to re-use tab washers......

 

B

bmp42

Active Member

Posts

658

Location

Coimbra, Portugal

• Dec 26, 2010

• #7

blue beasty said:

never a good idea to re-use tab washers......

Click to expand...

I never re-use and wonder why i get through so many per month!!

 

The Mad Hat Man

Well-Known Member

LZIR Despatch Agent

Posts

83,282

Location

Embasinga stocæ

• Dec 26, 2010

• #8

easy trick to miss is the tag on the INSIDE of tab washers - no point in locking the outside if the centre tab is missing.

 

L

Landysi

New Member

Posts

38

Location

Kidderminster,Worcestershire

• Dec 26, 2010

• #9

tab washers were all new and intact inluding the centre.

 

Pikey

Dummy Ejection Facilitator..

Posts

47,185

Location

in Baron Wet Bum's Slave pit..

• Dec 26, 2010

• #10

Are you bending the locking washer over both Inner and outer nuts??

I'
m sure you are but thought I'd ask so then it's removed from the equation.

 

L

Landysi

New Member

Posts

38

Location

Kidderminster,Worcestershire

• Dec 26, 2010

• #11

yes lock washer is bent over both inner and outer nut.

 

sypher

Well-Known Member

Posts

1,997

Location

Forest of dean

• Dec 26, 2010

• #12

are the bearings seating all the way home on the stub axle ? . sounds like there could be a burr on the stub holding the inner race away from being fully seated .

only way to know for sure is to remove the hub an see if the inner race slides all the way to the bottom of the stud . If not you have to sand/file off the burr on the stub till it does . that might cure your problem if the locking tabs etc are ok .