What have you done to your Landie today.

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Yes, as I suspected, the gear wheel had lost its grip on the spindle. I've notched it all the way round with a hammer and chisel so hopefully that'll give it a little more purchase. All working OK now. As it's still light I shall go out and wash it in a few minutes when I've drunk my coffee.
 
Felt a lot better about it. http://www.ebay.co.uk/itm/222165976791
Also got the world's best thing. It's a GP LR repair kit, consisting of, in SS :
10 x m6 x 60 coach bolt
10 x m6 x 30 as above
10 x m6 wingnut
10 x m8 washer
So far fixed both NS bumper end caps and wing minger. Total saving at stealership : one meelion spuids.
 
Fitted new uprated intercooler and aluminum radiator and some silicone hoses.
 

Attachments

  • IMG_20160710_183413.jpg
    IMG_20160710_183413.jpg
    267.9 KB · Views: 182
Walked into the garage to find the 90 was leaning over to the N/S/F corner yep you guessed it a flat tyre so bumped it up then removed all the 2a bits we bought last week and stored in the back of the 90 ( in the garage ) as the bench was full of crap from doing the 90's engine swap so bench cleared and recovered with new parts :D
 
Just got under the thing to bleed through new clutch fluid. The stuff that came out of the system was nasty, but no sign of leaks. I popped to the local motor factors for a piece of tubing which they assured me was correct, it wasn't. Anyhow, for the initiated, is there easier access to the bleed nipple as I could hardly get a spanner on the thing - Ed China makes it look easy, tw@.

Anyway, I have a good solid clutch pedal so I'm happy. Just got to fix the NS headlight which dips when main beam is selected this is as a result of some fog light wiring I removed from the engine bay.

Then an MOT.
 
It's my partner's birthday so we had a drive out to the east coast



Here's Skegness under a lowering sky


And a cute little tractor on the beach at Donna Nook



I was hoping to see seals, but there weren't any so I took a picture of the tractor instead.
 
Took the 110 for her Mot today, passed with advisories for 1 panhard rod bush and rear brake hose.
Picked up 2 new bushes (might as well once it's off and on the bench) as well as new nuts and bolts for both ends.
Got 3 new brake hoses because I can't see the front 2 lasting much longer as all 3 were replaced at the same time 12yrs ago and the system will need bleeding fully regardless.
£15.25p for 3 hoses, 2 bushes, 2 BIG bolts and 2 matched nuts.:D:D
 
well ive just about finished sanding my d1 down , ive removed the bumper and spots, also finished taking the sticky xs sticky stickers of the bottom of the doors. did I mention they were very sticky
 
doriz said:
Crazy value and congratulations on the MOT.
Click to expand...
She's never failed since the rebuild 12yrs ago but I replaced everything nearly!
I've only replaced the bits above, most of the poly bushes, all 4 discs and pads, new tyres and rebuilt the callipers again in those 12yrs.
Oh and the 2 short brake pipes callipers to flexi , they were fine but I couldn't get them off without damaging them when removing the callipers for the 2nd rebuild. Used stainless pistons this time though so expect more than 10yrs service life this time :rolleyes:
 
I removed the inlet manifold, intercooler cleaned all of the sludge out with petrol and changed the manifold gasket. Changed my horn and fitted a steering guard. The old girl is purring like a kitten and I think I have fixed the worst oil leaks.... Bonus!
 
You must log in or register to reply here.

Similar threads

B
defender 2.4 puma reverse light switch
Replies
4
Views
536
BEASTIE 90
B
Padda.116
300tdi disco 1, new head gasket oil leak!!
Replies
10
Views
629
Padda.116
Padda.116
Knappster
Shot-blasting steel wheels
Replies
9
Views
910
Knappster
Knappster
Mooky
Replacing thermostat
Replies
14
Views
553
Mooky
Mooky
I
Re-coding of ABS Module after repacement
Replies
10
Views
988
invisible999
I
Back
Top