That was cheap.
What have you done to your Landie today.
- Thread starter madfrank
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
That was cheap.
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
the_wolf
Well-Known Member
- Posts
- 16,791
- Location
- Stonehouse, Scotland
here ya go..... webasto fitted
tee piece into diesel pipe
bolted in place
with cubby box back in
my expert wiring
the exhaust
Looks a good bloody job that
.If my heaters werent so awesome i might even consider it myself
Andy Land
Well-Known Member
- Posts
- 4,499
- Location
- ... en route to Cuckoosville.
Finished fitting the CB at lunchtime in the office car park ... and forgot to bring a SWR meter ... oh well, won't switch the baby on until tonight then!
firepower
New Member
- Posts
- 450
- Location
- 29 Palms California.
Rear arches cut out to match the front. All of the plastic protectors removed "carefully" and lobbed in the skip. The person who designed the one that sits against the bodywork to "protect" the shocks needs his cock slamming in a full cutlery drawer. The foam sponge backing was fookin' soaking wet
Removing all of these has of course revealed a fortunately mild case of tin worm on the battery boxes and rear passenger side inner arch. I was contemplating removing the plastic sill covers but I know that the sills are shot so will leave them on until I have the box section replacements made
Removing all of these has of course revealed a fortunately mild case of tin worm on the battery boxes and rear passenger side inner arch. I was contemplating removing the plastic sill covers but I know that the sills are shot so will leave them on until I have the box section replacements made
bigvinnie
Active Member
- Posts
- 748
- Location
- Catterick North Yorkshire
Sold ma 90, more pennies for spares and shinny's on the 110!
First new job front wheel bearings and lowering back down to normal ride hide!
2inch lift is a pain in the arse, handles like a green goddess
First new job front wheel bearings and lowering back down to normal ride hide!
2inch lift is a pain in the arse, handles like a green goddess
Andy Land
Well-Known Member
- Posts
- 4,499
- Location
- ... en route to Cuckoosville.
SWR'd the CB now I've fitted it to the 110 but could only get it to 1.5 ... I know that's still ok but I had it to 1.1 on the old 90
I am using a short 0.8m springer though as opposed to a 1.8m I had on the 90 so I guess that's the difference.
I am using a short 0.8m springer though as opposed to a 1.8m I had on the 90 so I guess that's the difference.
mikescuba
Well-Known Member
- Posts
- 2,731
- Location
- France, Loire, Rhone Alpes
Took mine for a blast down the motorway on a 70 mile trip through wet/ snowy conditions. I past the time watching the water dripping down inside listening to the 200tdi rattling away, cruising at 70 mph and thought to myself " why does this still put a smile on my face"
I must get this bloody heater sorted out in the spring so I don't forget like I did last summer.
I must get this bloody heater sorted out in the spring so I don't forget like I did last summer.
handyman111
New Member
- Posts
- 1
Stated to find why my headlights wouldn't work last time I used them, got them sorted by fitting new power supply to the switch, now it won't turn over! Battery's fine, even Tryed a jump, got all dash lights and head lights still work. By passed key by shorting the starter motor, that spins but does not engage? Been working fine! As with the lights till yesterday! Think I might pull dash out tomorrow to see if I can find my gremlin behind their.....any ideas its a 1992 trip 200
Last edited:
johnny curt 1
Well-Known Member
- Posts
- 9,118
- Location
- manchester
new valves , valve guides , stem oil seals, thermostat , head gasket , timing chain , cam followers , full inspection , cleaned injectors and fully rebuilt the engine again
gemsdad
NOT BOTHERED.
- Posts
- 67,807
- Location
- halfway between here and there.
new valves , valve guides , stem oil seals, thermostat , head gasket , timing chain , cam followers , full inspection , cleaned injectors and fully rebuilt the engine again
did you not check the oil ring john.
discomark10
Well-Known Member
- Posts
- 3,977
- Location
- Milton Keynes
sounds like the feed from the batterie to the iginition barrel is fooked
johnny curt 1
Well-Known Member
- Posts
- 9,118
- Location
- manchester
what oil ring the ones on the pistons i had out and inspected ( run in bleddy lovely now them ) and the cylinders are lookin near perfect nice and evenly worn in
bive em a good old clean out with a bit of thinners and a scotchbrite pad
gemsdad
NOT BOTHERED.
- Posts
- 67,807
- Location
- halfway between here and there.
what oil ring the ones on the pistons i had out and inspected ( run in bleddy lovely now them ) and the cylinders are lookin near perfect nice and evenly worn in
yes mate,them ones.just a thought thats all.
johnny curt 1
Well-Known Member
- Posts
- 9,118
- Location
- manchester
yes mate,them ones.just a thought thats all.
i know matey i just wish id had a couple hours more daylight today as i still need to put the sump back on and fit a new oil filter
but while it was appart i took the oppertunity to go through it like a dose of the clap through a brothel
