jimbo87
New Member
- Posts
- 184
Noticed its marking it's territory, after 5k miles of no problems! So got underneath to have a look and it's got an oil leak on the sump, only a minor one though
What have you done to your Landie today.
- Thread starter madfrank
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
- Posts
- 8,543
- Location
- Tamworth, staffs.
Started fitting the raptor dash today.
The instructions say its a 20 minute job. Is it balls!
:frusty:
I have the bigger trunking behind the dash so had to cut the new dash. Its also a complete ball ache trying to cut the original dash with a junior hacksaw, Its even worse when the handle snaps and you have to use it by hand!:frusty:
Oh well, back for more tomorrow! :Cry:
The instructions say its a 20 minute job. Is it balls!
:frusty:I have the bigger trunking behind the dash so had to cut the new dash. Its also a complete ball ache trying to cut the original dash with a junior hacksaw, Its even worse when the handle snaps and you have to use it by hand!
:frusty:Oh well, back for more tomorrow! :Cry:
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
Just removed about a meter of exhaust and the backbox
It whistles now
It whistles now
Trewey
Cockernee, Pasty munchin bastid.
- Posts
- 20,088
- Location
- Kernow - Near England
why are you buying coil spring compressors?
not needed for any job on a landy and dangerous in use.
defender11069
AKA Mr cool...
- Posts
- 8,616
- Location
- up sh*t creek with out a paddle
i did mine with a cutting disc just to slots cb and radio on top panel on mine so no nead to cut it all off still tuck more than 20mins lolStarted fitting the raptor dash today.
The instructions say its a 20 minute job. Is it balls!
I have the bigger trunking behind the dash so had to cut the new dash. Its also a complete ball ache trying to cut the original dash with a junior hacksaw, Its even worse when the handle snaps and you have to use it by hand!
Oh well, back for more tomorrow! :Cry:
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
Just taken it for a drive and its rather loud……there were a few people who turned round when I floored it
Might need to put in a small silencer
Might need to put in a small silencer
Robbo5833
New Member
- Posts
- 194
To compress my...coil springs....I'll take my chances as to how dangerous... I've only been a mechanic for the past 14 years on everything from tanks to recovery trucks still got all 6 fingers on each hand
blue beasty
Leaks an prone to bits dropping off
- Posts
- 62,887
- Location
- Gloucestercotshirewolds
Dragged me poor old beast over to the Forest to have a chat with a couple of dodgy Landy types and pick up some stuff fer some even dodgier Landy types
Trewey
Cockernee, Pasty munchin bastid.
- Posts
- 20,088
- Location
- Kernow - Near England
but you don't need to compress them to fit or remove! even +2" ones.
Started fitting the raptor dash today.
The instructions say its a 20 minute job. Is it balls!
I have the bigger trunking behind the dash so had to cut the new dash. Its also a complete ball ache trying to cut the original dash with a junior hacksaw, Its even worse when the handle snaps and you have to use it by hand!
Oh well, back for more tomorrow! :Cry:
We had the same problem, if you want to bodge it then 30 minutes, we took 2 hours to get it all done, and then you have the problem of wiring everything in
All this took a while 
SHORT ROUND
Active Member
- Posts
- 675
- Location
- forest of dean, gloucestershire
Dragged me poor old beast over to the Forest to have a chat with a couple of dodgy Landy types and pick up some stuff fer some even dodgier Landy types
yeah and dumped half your bl**dy oil on our path lol
SHORT ROUND
Active Member
- Posts
- 675
- Location
- forest of dean, gloucestershire
fitted the tyre on my spare for my at road tyres so i can get rid of the drone using my mt all the time. oh and run all the wires for my winch just gotta install a cut off switch tomorrow and respool it
chunkymunky
New Member
- Posts
- 9,901
- Location
- worcestershire
Ordered bits for the conversion oh and got a halfords trade card....happy days.
buckshot
Well-Known Member
- Posts
- 9,841
- Location
- right yer!
finished off fabbing the X-member strengthing and NATO hitch for the 90 hopefully get time to weld it in place tomorrow (1 less job on the list of must do's )
welded a plate up behind the X-member just have to weld some strengthing plates off the bottom plate and up the rails when the thing is tacked on .
)
welded a plate up behind the X-member just have to weld some strengthing plates off the bottom plate and up the rails when the thing is tacked on .
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
Hmmmm I might need to paint my hitch after looking at that one
buckshot
Well-Known Member
- Posts
- 9,841
- Location
- right yer!
Hmmmm I might need to paint my hitch after looking at that one
that 1 is a brand spankin new 1
(not what you know but who you know )
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
that 1 is a brand spankin new 1
Bastid
I saw the new price on DB's site £280Ebay for ones in better condition for mine were £70+ but I was quite happy winning mine for £40, it works and its still built like a brick ****house so I'm happy to use it as a recovery point
buckshot
Well-Known Member
- Posts
- 9,841
- Location
- right yer!
Bastid
Ebay for ones in better condition for mine were £70+ but I was quite happy winning mine for £40, it works and its still built like a brick ****house so I'm happy to use it as a recovery point
been sitting in me shed for a 12 month (cooling off
)
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
