What have you done to your Landie today.

ShaunPDisco · Sep 30, 2014

Used the wifes credit card to treat the disco to some easy on parts as the MOT is next week!!

Looks like a weekend on my back with the disco on top!!

Animal88 · Sep 30, 2014

put some more nvo in her and flashed at a maroon D1 that had a big lift and big wheels. anyone on here?

Chrisw8 · Sep 30, 2014

reconnected brake pipe.

finished dismantling front bumper.

ThatJCB · Oct 1, 2014

chavvybloke said:
New to this site, but just wondered if anyone could help. I paid £120 plus parts to have a damper pulley replaced on a td5. ... Anyone every heard of this happening before, could the crank end be damaged??

You will probably get more replies if you start a new thread on that topic rather than piggybacking on an unrelated existing thread.

Regards

Chrisw8 · Oct 1, 2014

washed rubber bumper parts and doused metal bits in Fertan.

lcbandit · Oct 1, 2014

Driven it to work n put diesel in

muckmuck · Oct 1, 2014

Plugged an hole in my fuel tank....looks like I need a new one ....fitted my nice shiny gear knob

Animal88 · Oct 1, 2014

finally decided to put some air in my spare tyre so it is now usable again

Animal88 · Oct 2, 2014

fixed the poxy nsf door lock with a spring out of a spare drivers side lock. just need to remember that one now doesn't have one if I need to use it

landowner · Oct 2, 2014

Did some more on interior and fitted handbrake
Still cant decide where to put night heater, looking like front of tub in the middle

Chrisw8 · Oct 2, 2014

gave bumper 2 coats Bonda Primer

The Mad Hat Man · Oct 2, 2014

Removed ns front brake flexi and steel caliper pipes as they are corroded together

.

Morganholidayman · Oct 3, 2014

Not actually today but over last few days......
Bought a Mud bulkhead bar at LRO show and fitted that last Saturday, big improvement to comfort. Also bought a steering shield and fitted that yesterday. Happy now, for a while!

punkawallah · Oct 3, 2014

Stuck on a cheapo snorky from the Summer Range of Landy fashion from LR parts and tested all the mods to the heater made over the last few days and all the new lights as the old lot were rotten, fog lamp was actually full of water. The new bilge blower works much better than the Landy original one in me 1990 110 CSW

timtheenchanteruk · Oct 3, 2014

recieved a few bits n bobs, couple of spares and some bits to go on this next week one evening if its nice out

a2dds · Oct 3, 2014

My power steering pump to box pipe has rubbed and is now leaking. Its the metal part of the pipe but I can't seem to find a direct replacement for the whole metal and rubber pipe.

I have a td90 with a 200tdi fitted and wondered if something strange has been made up to fit it. Here is a joint between the metal pipe and rubber flexi bit
http://tapatalk.imageshack.com/v2/14/10/03/4b895e7a2cbc28042098
e067bd8b7ef6.jpg

The rubber hose is then adapted back to a metal pipe that bends round into the pump. Bit hard to see but its down there!

Anyone have any idea if this is a part I can buy or do I have to get each individual part and make it up.

Did notice that the long metal pipe from the box doesn't seem to be bent in the correct ways so it sticks out a fair bit.

punkawallah · Oct 3, 2014

a2dds said:
My power steering pump to box pipe has rubbed and is now leaking. Its the metal part of the pipe but I can't seem to find a direct replacement for the whole metal and rubber pipe.

I have a td90 with a 200tdi fitted and wondered if something strange has been made up to fit it. Here is a joint between the metal pipe and rubber flexi bit
http://tapatalk.imageshack.com/v2/14/10/03/4b895e7a2cbc28042098
e067bd8b7ef6.jpg

The rubber hose is then adapted back to a metal pipe that bends round into the pump. Bit hard to see but its down there!

Anyone have any idea if this is a part I can buy or do I have to get each individual part and make it up.

Did notice that the long metal pipe from the box doesn't seem to be bent in the correct ways so it sticks out a fair bit.

By coincidence I have just come back from Halfrauds with 2 rolls of FIXX-IT tape to do a temp job on me filter to turbo pipe and this may well get you out of trouble for a bit. It is one of these self bonding silicone thingiebobs good for up to 500 psi if you believe the blurb.

a2dds · Oct 3, 2014

punkawallah said:
By coincidence I have just come back from Halfrauds with 2 rolls of FIXX-IT tape to do a temp job on me filter to turbo pipe and this may well get you out of trouble for a bit. It is one of these self bonding silicone thingiebobs good for up to 500 psi if you believe the blurb.

Ha cheers for that. Ide rather replace as soon as pos. I can drive my work van about but rather have me landy! Does that stuff work on metal?

punkawallah · Oct 3, 2014

a2dds said:
Ha cheers for that. Ide rather replace as soon as pos. I can drive my work van about but rather have me landy! Does that stuff work on metal?

Metal ,plastic etc they claim and it's good for sealing and insulating up to 8000 volts but it's too wet for me to go outside to test it. Only reason I bought it is that there is a minor age related leak in me intake pipes [and in the 110 too

]and I can't find a new set of hoses at reasonable price for the 2.5TD, all the sites show from TDI onwards only.

The Mad Hat Man · Oct 3, 2014

found out my brake pipe flaring tool is ****e

What have you done to your Landie today.

Active Member

Active Member

Well-Known Member

Member

Well-Known Member

Well-Known Member

Active Member

Active Member

Active Member

Pensioner Pete

Well-Known Member

Well-Known Member

Member

Member

Well-Known Member

Active Member

Member

Active Member

Member

Well-Known Member

Similar threads