discomark10
Well-Known Member
- Posts
- 3,977
- Location
- Milton Keynes
is that with diff lock engaged?
What have you done to your Landie today.
- Thread starter madfrank
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
is that with diff lock engaged?
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
welding, messing and general repairs
danny6801
Well-Known Member
- Posts
- 1,665
- Location
- North Wales
Finished taking the engine and boxes out of scrap Discovery
.
Lookin good won't be long before you will be flying around everywhere.
- Posts
- 10,639
- Location
- Oxfordshire
undersealing with a brush..... nightmare nightmare nightmare nightmare nightmare nightmare nightmare nightmare nightmare rain rain rain nightmare nightmare nightmare nightmare
flat
Well-Known Member
- Posts
- 9,075
- Location
- Far away from you!!
Yeah fecking nightmare. I gave up doing it with a brush and borrowed a compressor.
Chrisw8
Well-Known Member
- Posts
- 1,980
- Location
- Top of the Hill
started rebuilding n/s front wheel bits
nrgserv
Well-Known Member
- Posts
- 4,208
- Location
- shipley, west yorks.
A frame ball joint at a guessRight. Got a problem. I think.
Lots of play on the front prop but this is while the hand break is on so can't compare with the rear prop. (I shall compare when it's light tomz!).
Also getting a one of thud or knock as I go into corners are put in gear and out foot down. Or come of the accelerator suddenly. Is this something I should be worrying about/am I being paranoid. Plus anyone know what might be causing it? I'm guessing the spline is worn out (or what ever the cog bit on the end of the prop is called)
bunnymofo
New Member
- Posts
- 563
- Location
- aberdeenshire
cut out rear body X member and am half way thru making a new one
Trying to work out this Haynes manual thing.
Anyone know how to find out how much oil I need for a service. Going to change ALL of the oil, engine, gearbox, axles and anywhere else which has the stuff.
Flaming thing doesn't have a proper index
Anyone know how to find out how much oil I need for a service. Going to change ALL of the oil, engine, gearbox, axles and anywhere else which has the stuff.
Flaming thing doesn't have a proper index
jamesmartin
Well-Known Member
- Posts
- 91,879
- Location
- louth lincs
if you get 10 litres for engine and 5 litres for gear box and 10 for axles t/box etc you will have some left over and its cheaper in 5 litres from motor factors
the_wolf
Well-Known Member
- Posts
- 16,791
- Location
- Stonehouse, Scotland
Each axle takes about 1.5 litres. Swivels are about 0.5 litres each. Engine oil is 6 litres. Gearbox is 2.5 litres. Can't mind the transfer box off top of my head but if you've bought enough EP90 just fill it till it pours back out.
Thank you
So thats 10 litres of diesel engine oil, 5 litres of ATF for gearbox and 10 litres of the EP90
Have I got that the right way round
SteNova
Well-Known Member
- Posts
- 2,200
- Location
- N. Wales, LL22
and 5 liters of antifreeze while your at it
gemsdad
NOT BOTHERED.
- Posts
- 67,807
- Location
- halfway between here and there.
Hmmm, there wont be room the radiator filler thing is almost to the top
piece of tube and drain some out.
flat
Well-Known Member
- Posts
- 9,075
- Location
- Far away from you!!
just drain and flush your coolant every couple of years and renew. if it isnt using any then fine dont worry about it
