htr
Well-Known Member
- Posts
- 1,557
- Location
- Central Otago, Southern New Zealand
Ordered a new VCU and bearings, diff side seals, gear lever gator, bulb holders and wiring to do the rear light upgrade and a new coolant bottle and cap. 
What have you done to your Freelander today
- Thread starter Freelaner
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Tempus Fugit
Well-Known Member
- Posts
- 17,712
- Location
- Great Britain
Driver's rear window went down, twanged and didn't come back up.
Oh well to be expected. Replacement ordered.
Oh well to be expected. Replacement ordered.
GrumpyGel
Well-Known Member
- Posts
- 26,391
- Location
- Christchurch, New Zealand
myotherworld
Active Member
- Posts
- 182
- Location
- Birmingham
Hello Black...Goodbye Grey..
Amazing What A Couple Of Cans Of Boot Polish Can Do
you want to give the kids that spray painted your number plates a good talking to. little buggers
nice work on bumpers
GrumpyGel
Well-Known Member
- Posts
- 26,391
- Location
- Christchurch, New Zealand
Oh dear - does it sound serious? Silly question really cos any sound originating from the IRD is serious!
If you need to rebuild it, I can recommend the bearing/cooler/seal kit from One Stop Gearbox Shop
I rebuilt my IRD with one of their kits (cost about £150) and it has been running fine for a couple of years now. I gave the IRD & kit to a 'diff shop' here in Chch as I didn't want to bugger around pulling and pushing bearings and f****g it up - but I believe you have tools/experience to do that yourself. Their report back to me was that a couple of seals were missing from the kit that they had to source. The kit didn't contain new 'shims'. I didn't even consider them at the time and I don't know if the diff shop renewed them - I don't know how important they are.
Using one of these kits relies on your crown & pinion gears being in good nick (mine were trashed) - they're quite a common part listed on eBay/Landie stores, but have no experience of them as I rebuilt 2WD by removing gear on the end of the pinion. I'm looking to reinstate 4WD - so will probably be getting some though
If you need to replace the crown/pinion gears, the price starts getting closer to just getting a recon IRD and replacing it. Be careful though, I looked around and I wouldn't trust a lot of the outfits to do a proper job (eg replace the gears with new). In fact I wouldn't even trust them with my neighbour's Landcruiser!
Last edited:
openfold
Member
- Posts
- 84
- Location
- Fareham, Hampshire
Fitted MG F rear view mirror with lights in my 3 door, they come on when the doors are opened and the car is unlocked too. I also painted my drums, they were letting the car down with the scabby rust they were covered in.
GrumpyGel
Well-Known Member
- Posts
- 26,391
- Location
- Christchurch, New Zealand
Nice Tiki - actually Heitiki.
openfold
Member
- Posts
- 84
- Location
- Fareham, Hampshire
Thanks
it was my grandmas, she loved NZ. It has tiki in quotes on the back and then New Zealand green stone, or something to that effect
GrumpyGel
Well-Known Member
- Posts
- 26,391
- Location
- Christchurch, New Zealand
Thanks
lol, I have another iconic Kiwi Souvenir Shop gift - a Ponga Vase - that was my grandmas
Members of our family have migrated to and from NZ quite regularly over the last 60 years!Hijacking the thread a bit here - so.....
Took the Freelander for its WOF (MOT) today - passed with flying colours. Mind you the guy who tested it must have pressed every button he could find cos the rear window was open when I picked it up - and the sun roof - does he not know that you should NEVER press the button to open the sunroof on a Freelander! It will probably leak like a sieve now.
htr
Well-Known Member
- Posts
- 1,557
- Location
- Central Otago, Southern New Zealand
lol, I have another iconic Kiwi Souvenir Shop gift - a Ponga Vase - that was my grandmas
Hijacking the thread a bit here - so.....
Took the Freelander for its WOF (MOT) today - passed with flying colours. Mind you the guy who tested it must have pressed every button he could find cos the rear window was open when I picked it up - and the sun roof - does he not know that you should NEVER press the button to open the sunroof on a Freelander! It will probably leak like a sieve now.
Whaaat! haven't you disconnected dat sunroof yet?
openfold
Member
- Posts
- 84
- Location
- Fareham, Hampshire
lol, I have another iconic Kiwi Souvenir Shop gift - a Ponga Vase - that was my grandmas
Hijacking the thread a bit here - so.....
Took the Freelander for its WOF (MOT) today - passed with flying colours. Mind you the guy who tested it must have pressed every button he could find cos the rear window was open when I picked it up - and the sun roof - does he not know that you should NEVER press the button to open the sunroof on a Freelander! It will probably leak like a sieve now.
Glad it got through
next time you might have to pull the fuse or disconnect the switch. if it leaks have one of those umbrella hats with you haha :bounce:Oh dear - does it sound serious? Silly question really cos any sound originating from the IRD is serious!
If you need to rebuild it, I can recommend the bearing/cooler/seal kit from One Stop Gearbox Shop
I rebuilt my IRD with one of their kits (cost about £150) and it has been running fine for a couple of years now. I gave the IRD & kit to a 'diff shop' here in Chch as I didn't want to bugger around pulling and pushing bearings and f****g it up - but I believe you have tools/experience to do that yourself. Their report back to me was that a couple of seals were missing from the kit that they had to source. The kit didn't contain new 'shims'. I didn't even consider them at the time and I don't know if the diff shop renewed them - I don't know how important they are.
Using one of these kits relies on your crown & pinion gears being in good nick (mine were trashed) - they're quite a common part listed on eBay/Landie stores, but have no experience of them as I rebuilt 2WD by removing gear on the end of the pinion. I'm looking to reinstate 4WD - so will probably be getting some though
If you need to replace the crown/pinion gears, the price starts getting closer to just getting a recon IRD and replacing it. Be careful though, I looked around and I wouldn't trust a lot of the outfits to do a proper job (eg replace the gears with new). In fact I wouldn't even trust them with my neighbour's Landcruiser!
I have managed to source a used IRD thats in decent condition, I have just ordered a new VCU (the one that was on had only done 30000 miles bought from bell engineering and is now no good
) and a new setof tyres are on the way. Just need to have a peek at the rear diff and see what its like. Fitting the IRD tomorrow so hopefully all will be well and sorted for my trip down to Goodwood and the festival of speed in a few days
Thanks for the info re rebuild I will be rebuilding the old one all being well
Changed the front right ABS sensor as its resistance was much higher than the others.
The old one came out very easily since it was only changed about a year or so ago....cheap chinese parts strike again. What have I replaced it with? another cheapo unbranded ebay special. Im not a fast learner.
Anyway, changed the sensor and within a quarter of a mile the three amigos went out and normal service is resumed.
The old one came out very easily since it was only changed about a year or so ago....cheap chinese parts strike again. What have I replaced it with? another cheapo unbranded ebay special. Im not a fast learner.
Anyway, changed the sensor and within a quarter of a mile the three amigos went out and normal service is resumed.
Epicuser
Ex Freelander Owner
- Posts
- 2,393
- Location
- North East Surrey
Sold it. (A week ago)
DastardlyDan
Active Member
- Posts
- 287
Tried a new wiring mod, for more low-end poke on the L series.
Worked REALLY well, but brings on the engine warning light once you rev it hard :lol:
Worked REALLY well, but brings on the engine warning light once you rev it hard :lol:
Similar threads
