What have you done on your 90/110/130 today?

Al2O3 · Jun 30, 2020

New swivel pin bearings fitted to nearside.
All 13 of the previous roller bearings recovered.

I reckon this was due to the pre-load not being high enough. I've taken a couple of wafer thin shims out and judged it by hand. Rather than my fishing scales

Refitted the turbo after taking it off and cleaning it out with brake fluid. The oil outflow pipe is a b@stard to fit and I'm certain that is the root of my turbo/oil consumption problem.

frog hopper · Jul 7, 2020

CT (mot) due in 10 days time, thought I aught to strip the rear brake drums and clean the dust out and re-adjust.
Struggled to get the drums off, and when I did they were worn and scored badly. My fault for not cleaning them out after a lot of off-roading this last autumn I suppose.
New drums, shoes and springs ordered, should be putting everything back together before the weekend, I hope.
Will post some picks of badly maintained rear brakes for you to laugh at in the next day or two.

frog hopper · Jul 8, 2020

Well, knock me down with a feather !!
Brake bits ordered yesterday just after lunch turned up this morning

actually got one side fitted 24 hours after ordering. Job done now and road tested, all OK, will re-adjust in a few days time when the whole lot has bedded in a bit.
Anyway; this is a badly maintained rear brake.

Spot the difference

And just for a bit of tool porn as the camera was out, one of my bestest mates.

A good bit of kit, paid £25 for it at a sortout 20 years ago, it was old and knarley then, but never lets me down.

frog hopper · Jul 9, 2020

Feeling a bit chuffed with having fixed something without it turning into the usual drama, decided to fettle the front prop and put the joints 45 deg out of phase as advised on here by someone ages ago. Sorry can't remember who.

Test drive and a quite nasty judder, esp under load. Oh fiddle, or words to that effect, Put everything back as was, no difference, worse if anything. Double pigging fiddle,

Check rear brakes for binding, seems to be OK. Check joints on rear prop, perhaps just a touch loose on the rearmost joint, take prop off and the rear joint is now flapping about like something has suddenly turned to jelly.
As luck would have it I have new GKN joints in stock so change it, will re-fit the prop and test tomorrow.

Feckin Land Rovers. Just for a minute there I thought I had started to get on top of the list.

Hicap phill · Jul 10, 2020

Just drove a few easy lanes to find a friend an overnight stopover.
Then found I need 2 new door hinges these are only a year old. Looks like I might get some better ones (or take the old ones of the other doors

)

frog hopper · Jul 13, 2020

Replaced rear prop after changing the diff end UJ, now drives as normal, so happy bunny once again.

frog hopper · Jul 15, 2020

The 90 passed her CT (mot) today

3 advisories, 1st one being that it was apparent that rust in chassis had been repaired. (doh)
2nd that there was a dent in the r/h wing - but not posing a danger to others.
3rd that there was a dent in the l/h door - but not posing a danger to others.
All above comments were just part of the modern system.
I did wonder if any comment would be made about the colour scheme.

Chalky. · Jul 16, 2020

I looked at mine after I got back from work.

Beer in hand, I was mentally thinking out what I need/want to do to her! Then I started panicking about how much money I've already spent on it, quietly turned around and fetched another beer. Not so much panic now!!

miktdish · Jul 16, 2020

Hicap phill said:
Just drove a few easy lanes to find a friend an overnight stopover.
Then found I need 2 new door hinges these are only a year old. Looks like I might get some better ones (or take the old ones of the other doors )

Or buy some oil and squib it in from time to time ?

Knappster · Jul 21, 2020

Another 12 months MoT. Just needed the fog light switch fettling as it was playing up

and a small bit of welding to the front crossmember. Not bad for a 31 year-old vehicle.

miktdish · Jul 22, 2020

Took the rear wheel off and had a look at the brakes, and burst into tears .... 1994 300tdi my arse, fully rebuilt in 2015

Maggsie8 · Jul 22, 2020

Fixing more of the previous owners bodge jobs

Replaced the front prop-shaft for a heavy-duty double cardan (the previous owner had put a lift on but decided to leave the original shaft on, hence f**k UJs!!)
Replaced all bushes (replaced with cheap cr*p by the previous owner, but rather than use a vice to put the radius arm bushes in properly, decided it was better to cut them in half to fit them, then fitted dry and therefore the bolt and sleeves fused together... 4 hours of cutting bolts out )

Some people should be banned from owning Landy's... Pic's included to allow you to have a laugh at my expense

Hicap phill · Jul 22, 2020

@Maggsie8 them bushes are made like that. Easier to change

(only if they use lube on the bolts/sleeves)
keep on looking for more work. It will keep giving

Hub · Jul 22, 2020

Insurance is due in the next few weeks - comparison sites say it’s a van??!!! What happened overnight? The vehicle looks the same, drives the same, no windows have been taken out and replaced by panels....it was a car last year, and the year before and all the years before! So what has changed?

neilly · Jul 22, 2020

Fitted the new sump, although did find after removal that the old squashed sump had not affected the pick up sieve.

Hey ho.

Cheers

frog hopper · Jul 22, 2020

miktdish said:
Took the rear wheel off and had a look at the brakes, and burst into tears .... 1994 300tdi my arse, fully rebuilt in 2015

View attachment 215255
View attachment 215256

Did your calipers actually contain any fluid? I'm surprised all that rust is holding together.
If you can get them off it's not a total disaster, there pretty cheap to replace.
Good luck.

miktdish · Jul 23, 2020

frog hopper said:
Did your calipers actually contain any fluid? I'm surprised all that rust is holding together.
If you can get them off it's not a total disaster, there pretty cheap to replace.
Good luck.

The brakes did work (quite well too) despite the other side looking very similar. The front calipers look better (or should I say, less rusty) ...

resto_d1 · Jul 23, 2020

Gottschalk said:
I looked at mine after I got back from work.

Beer in hand, I was mentally thinking out what I need/want to do to her! Then I started panicking about how much money I've already spent on it, quietly turned around and fetched another beer. Not so much panic now!!

this is my life!!! I even stopped drinking for a week as kept doing that lol.

resto_d1 · Jul 23, 2020

Woke up, checked it was still outside the window and waiting patiently for nanocom to turn up....

JimS · Jul 23, 2020

Slowly working my way round the chassis and cross members with airline, brush, Jenolite, Dinitrol cavity wax etc. Taking my time over it doing it bit by bit.
Only found a couple of very small areas (so far) that need remedial, one I've rounded off and made into a drain hole, the other needs a 2x1 plate
Surprisingly clean and solid really. Had repaired the rear cross member a few years ago and it has remained good, no rust returning so pleased about that.
Once all done will give it a blast over with Dinitrol chassis paint

What have you done on your 90/110/130 today?

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Guns n Chainsaws

Well-Known Member

Guns n Chainsaws

Active Member

Attachments

Well-Known Member

Active Member

Well-Known Member

Well-Known Member

Guns n Chainsaws

Well-Known Member

Well-Known Member

Well-Known Member

Similar threads