- Posts
- 23,051
- Location
- In the next Glen
Haha I was trying to clean my key board, I was going to say you could just get your mate to do them the next time lol
Other what have u done on ur disco today
- Thread starter gstuart
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Haha I was trying to clean my key board, I was going to say you could just get your mate to do them the next time lol
discodrivercumbria
Well-Known Member
- Posts
- 3,317
- Location
- South lakes
started on the broken wire in the loom, right up under the dash drivers side, need hands like a Midget! eyes like a hawk and a bit of contortionism to get in!
Henry_b
Think outside, no box required.
- Posts
- 15,509
- Location
- somewhere else
cruised down the M5, i practically live on that M'way.
She behaved herself at 70-80mph nice and quiet!
30mpg
She behaved herself at 70-80mph nice and quiet!
30mpg
stuu
Well-Known Member
- Posts
- 1,949
- Location
- Aberdeenshire
well 500 mile into the 191k d2 bought just by looking underneath for rot. let it idle for 5 mins and just said I'd have it.
levels still good.
dry underneath.
it's been ****ing down for hours still dry inside.
been offered mk4 golf reccaro leathers for very cheep absolutely comfy things heated too (discos currently cloth heated) so may attempt that one day
levels still good.
dry underneath.
it's been ****ing down for hours still dry inside.
been offered mk4 golf reccaro leathers for very cheep absolutely comfy things heated too (discos currently cloth heated) so may attempt that one day
TorsionBhudda
Well-Known Member
- Posts
- 1,342
- Location
- Falkirk
Fitted skimmed exhaust manifold and new Wurth manifold studs just got the new turbo to fit tomorrow.
stuu
Well-Known Member
- Posts
- 1,949
- Location
- Aberdeenshire
polished up headlight lenses.
egr deleted and the vac lines and solenoids.
cleaned out the map sensor.
egr deleted and the vac lines and solenoids.
cleaned out the map sensor.
Helicoiled SWMBO's aux belt tensioner stud back in place after the bleddy thing fell out 
- tensioner just sat there in the fan blades, watching the world go past .... trashed the belt tho ... but I guess a new belt and half an hour to fit the coil, and then loctited* the whole "arrangement" back together was an easy fix ....
Thus far, HG seems to have survived it's few mins without a water pump too ..... but I'm not holding my breath
* - Loctite 638 anorl - get out of that ya bar steward
- tensioner just sat there in the fan blades, watching the world go past .... trashed the belt tho ... but I guess a new belt and half an hour to fit the coil, and then loctited* the whole "arrangement" back together was an easy fix ....Thus far, HG seems to have survived it's few mins without a water pump too ..... but I'm not holding my breath
* - Loctite 638 anorl - get out of that ya bar steward
Fitted new viscous fan to the Disco...roars like a jet on start up.... unlike the old unit. Can someone tell me what the normal working temps for the TD5 engine are...
My nanocom just throws up High Temp warnings at 91c. Is it being over cautious ??
My nanocom just throws up High Temp warnings at 91c. Is it being over cautious ??
Shimsteriom
Master Procrastinator
- Posts
- 41,905
- Location
- Over Here
Nowt, coz it's still not broke
However, I've found myself looking for a replacement front bumper that has recovery points on it.
However, I've found myself looking for a replacement front bumper that has recovery points on it.
Henry_b
Think outside, no box required.
- Posts
- 15,509
- Location
- somewhere else
Stapled me headliner!
Henry_b
Think outside, no box required.
- Posts
- 15,509
- Location
- somewhere else
The old D2 is trying to wear a hole in its pipes!
So i just got some old rubber pipe, cut it down the centre and slid it over the metal pipe.
Much better.
Low tech solution I grant you..
But it works!!
So i just got some old rubber pipe, cut it down the centre and slid it over the metal pipe.
Much better.
Low tech solution I grant you..
But it works!!
Lazydave
Well-Known Member
- Posts
- 194
- Location
- Birmingham
Fitted D4 secondary turbo oil drain pipe modification.
What a b!#&h to remove and refit the starter motor on the drive.
What a b!#&h to remove and refit the starter motor on the drive.
Last edited:
Lazydave
Well-Known Member
- Posts
- 194
- Location
- Birmingham
I used copper pipe lagging on mine held with cable ties!The old D2 is trying to wear a hole in its pipes!
So i just got some old rubber pipe, cut it down the centre and slid it over the metal pipe.
Much better.
Low tech solution I grant you..
But it works!!
RogerStenning
Active Member
- Posts
- 245
- Location
- South London
Hi well they say things happen in three's here's what I've done to my disco td5 end of last year o/s/r brake pipe corroded renewed all pipes. Christmas ACE pipe let go ripped it all out and replaced with modified block and hydraulic hose . Then 2 weeks ago high pressure fuel pipe ( green one) common issue rubbed and sprayed diesel everywhere just got back from garage though the first two I did myself and the fuel pipe I could have done but with work it would have sat for a while longer also serviced it fingers crossed that's it for a while
- Posts
- 23,051
- Location
- In the next Glen
Picked up a trailer for 200 bangers got a cover with it now im getting a fleet of trailers to go with my landys
First job get rid of the jaggy ar$e brambles
First job get rid of the jaggy ar$e brambles
- Posts
- 23,051
- Location
- In the next Glen
Returned a couple of motor bikes out my unit to there owners Free rent space is over !!
Then took my Sankey to its new living quarters to get converted for camping
Then took my Sankey to its new living quarters to get converted for camping
discodrivercumbria
Well-Known Member
- Posts
- 3,317
- Location
- South lakes
moved it to wash the Hilux!
