notenoughtime
Active Member
- Posts
- 439
- Location
- Essex
Other what have u done on ur disco today
- Thread starter gstuart
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Marmaduke
Well-Known Member
- Posts
- 9,773
- Location
- Near the land of 'Me Duck'
neilly
Well-Known Member
- Posts
- 20,000
- Location
- Oxfordshireness
notenoughtime
Active Member
- Posts
- 439
- Location
- Essex
Only if you want sympathy
Sorry for your loss, of money and time that is
I must be mad lol
Marmaduke
Well-Known Member
- Posts
- 9,773
- Location
- Near the land of 'Me Duck'
How much damage is done to it?
notenoughtime
Active Member
- Posts
- 439
- Location
- Essex
I'm not sure what but think there is a twig stuck in the roof bars lol
Marmaduke
Well-Known Member
- Posts
- 9,773
- Location
- Near the land of 'Me Duck'
Is it cat c or d?
notenoughtime
Active Member
- Posts
- 439
- Location
- Essex
Cat D
Needs bonnet, wing and screen
Screen ordered and will be in Tuesday just need to find a wing and bonnet and snorkel to finish it off I think
Needs bonnet, wing and screen
Screen ordered and will be in Tuesday just need to find a wing and bonnet and snorkel to finish it off I think
neilly
Well-Known Member
- Posts
- 20,000
- Location
- Oxfordshireness
Is this the one that was scrapped last month by one of the members on here after being hit by a tree in a storm?
Cheers
notenoughtime
Active Member
- Posts
- 439
- Location
- Essex
Don't think so! Is there a link to it?
Co-Pang-Yang
Well-Known Member
- Posts
- 2,930
- Location
- Colchester, Essex
Well bored at work after getting back early so decided to take my passenger central locking actuator apart after reading up on them getting gummed up.
Finally pulled it apart and bits went everywhere but it wasn't seized. Put a battery too it and the motor was working but not sure if I've got it put back together again properly now.
Checked power on the car and when I lock or unlock it getting between 0.0 and 0.05 volts to the passenger actuator.
So not got a possibly broken actuator and an electrical fault somewhere on the car.
Decided best option is to put the door card back on and continue locking and unlocking the door from the inside.
Finally pulled it apart and bits went everywhere but it wasn't seized. Put a battery too it and the motor was working but not sure if I've got it put back together again properly now.
Checked power on the car and when I lock or unlock it getting between 0.0 and 0.05 volts to the passenger actuator.
So not got a possibly broken actuator and an electrical fault somewhere on the car.
Decided best option is to put the door card back on and continue locking and unlocking the door from the inside.
Magicgrotto
Well-Known Member
- Posts
- 2,769
- Location
- doncaster
Co-Pang- yang , Have you thought about the silly spring in the door lock ??
SteveClv
Active Member
- Posts
- 145
- Location
- Sherborne, Dorset
Took my fan cover off and noticed a pesky weep of oil coming from the camshaft cover - pulled it off to find that the O ring was completely flat and someone had stuck it back in with RTV so popped down to OandO in Henstridge and got a new one, along with 2 new oil filters and a set of brake pads (tomorrows job)
Installed the new O ring, dropped the engine oil and replaced it with some synthetic that I picked up cheap at the auction along with some Molyslip.
Installed the centrifugal oil filter but found that the bolts were turning ominously when tightened as if they were stripped - ran the engine up to temp and no sign of any leak or weepage but will have to keep an eye on it. Gave up on doing the main filter as not sure how to grip it just yet - will revisit.
Then decided to check the diff oil levels - first plastic bolt came out from the front diff and the rear one rounded off - so another job for another day - replace both with brass ones.
Finally went to replace the headlamp washer pump only to find that the used parts guy had sent me one of a facelift rather than the earlier ones. Big difference!
Installed the new O ring, dropped the engine oil and replaced it with some synthetic that I picked up cheap at the auction along with some Molyslip.
Installed the centrifugal oil filter but found that the bolts were turning ominously when tightened as if they were stripped - ran the engine up to temp and no sign of any leak or weepage but will have to keep an eye on it. Gave up on doing the main filter as not sure how to grip it just yet - will revisit.
Then decided to check the diff oil levels - first plastic bolt came out from the front diff and the rear one rounded off - so another job for another day - replace both with brass ones.
Finally went to replace the headlamp washer pump only to find that the used parts guy had sent me one of a facelift rather than the earlier ones. Big difference!
neilly
Well-Known Member
- Posts
- 20,000
- Location
- Oxfordshireness
@SteveClv
Having fun yet?
Centrifugal oil filter bolts are known to strip quite easily, a lot of people end up using a nut and bolt.
Main filter I use a nylon strap filter wrench. utilises a 1/2 or 3/8 ratchet drive. Only a few quid.
Good call with the Diff plugs, also FYI, have a look at the coolant bleed plug in the top hose, there is an ally replacement for it as they can fail as well if you ever need to bleed it.
Cheers
Having fun yet?
Centrifugal oil filter bolts are known to strip quite easily, a lot of people end up using a nut and bolt.
Main filter I use a nylon strap filter wrench. utilises a 1/2 or 3/8 ratchet drive. Only a few quid.
Good call with the Diff plugs, also FYI, have a look at the coolant bleed plug in the top hose, there is an ally replacement for it as they can fail as well if you ever need to bleed it.
Cheers
SteveClv
Active Member
- Posts
- 145
- Location
- Sherborne, Dorset
Loving it - at least you can pretty much get at everything unlike my pesky Mercedes B Class!
I'll check the coolant one although I may invest in a silicone one along with a new fanbelt.
Just found out that the wastegate has a label from Universal Turbochargers on - so may be a rebuilt turbo or an upgraded one - emailed them to see if they either have records or if there is some way of telling.
I'll check the coolant one although I may invest in a silicone one along with a new fanbelt.
Just found out that the wastegate has a label from Universal Turbochargers on - so may be a rebuilt turbo or an upgraded one - emailed them to see if they either have records or if there is some way of telling.
Co-Pang-Yang
Well-Known Member
- Posts
- 2,930
- Location
- Colchester, Essex
Co-Pang- yang , Have you thought about the silly spring in the door lock ??
Don't think it's that cause the actuator isn't getting any power when I activate the remote locking fob.
Seems to be a cut in the power somewhere.
Marmaduke
Well-Known Member
- Posts
- 9,773
- Location
- Near the land of 'Me Duck'
Washed and waxed mine then had a day stripping my 2a ready for shotblasting
joojar
Active Member
- Posts
- 158
- Location
- Derbyshire
Changed the top hose, for what must be the 5th or 6th time. Wet and dried the metal pipes where the hose pushes on this time, have an idea that scale and pitting has been contributing to leaks. We'll see if it does any good...
Continued doing bits & bobs from 144k service, got a list of "matters arising" to attend to, including front axle breather chafing on radius arm. Looking at the routing, I can't work out why it *wouldn't* chafe, so not sure WTF can be done about it
Continued doing bits & bobs from 144k service, got a list of "matters arising" to attend to, including front axle breather chafing on radius arm. Looking at the routing, I can't work out why it *wouldn't* chafe, so not sure WTF can be done about it
GingerPuss
Active Member
- Posts
- 232
- Location
- Southport
I was productive today. I managed to:
Of course when removing the EGR I dropped a small extension bar with an 8mm socket attached. It dropped down into a black hole. Couldn't find it anywhere. No doubt it will drop out onto the road or my driveway at some point.
- Delete the EGR valve with a blanking kit
- Replace the auxiliary serpentine belt with a new one
- Replace the belt tensioner pulley with a new one (chirping noise when cold is now cured)
Of course when removing the EGR I dropped a small extension bar with an 8mm socket attached. It dropped down into a black hole. Couldn't find it anywhere. No doubt it will drop out onto the road or my driveway at some point.
