- Posts
- 33,599
- Location
- North Shropshire
What did you do with your Range Rover today
- Thread starter Dopey
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Datatek
Well-Known Member
- Posts
- 44,883
- Location
- Near Poitiers SW France
Sounds like a very good idea to me.
Datatek
Well-Known Member
- Posts
- 44,883
- Location
- Near Poitiers SW France
I had a screen come unstuck on a brand new Volvo years ago. I was running grandma home and she kept complaining it was cold in the car, I was roasting. Next day in daylight, I noticed the screen on the passenger side had come completely away from the A post.
- Posts
- 33,599
- Location
- North Shropshire
I'm not sure if they'll 'suit ' bring black wheels on a grey car but I've never cared about looks
So you'd rather strip the seat covers, once you've got the seat out, removed the trim & switch panel, then find out the foam rips when you peel the heat pads away, wait for new foam pads, refit then try & remove the wrinkles that were not there before?
Interesting.
Admittedly I have prior experience, the rear Peltier takes about 25 minutes to R&I, the lower one about 15 minutes - neither are explainable, you need to see 'how' then it makes sense.
- Posts
- 4,653
- Location
- Rotherham
RangeRoller dt
Well-Sprung Member
- Posts
- 14,393
- Location
- Trapped inside my head @ LZ asylum
It is winter mate
Ah I see, not for now you mean. Seems good idea and the colour may grow on you.
- Posts
- 33,599
- Location
- North Shropshire
Colour?It is winter mate
Ah I see, not for now you mean. Seems good idea and the colour may grow on you.
- Posts
- 33,599
- Location
- North Shropshire
Who?
- Posts
- 12,628
- Location
- Sud ouest France !
When ?
- Posts
- 33,599
- Location
- North Shropshire
Not Málaga, i hope, they're having it a bit rough
- Posts
- 4,653
- Location
- Rotherham
What?
- Posts
- 33,599
- Location
- North Shropshire
Drove to work, heater on full, really need to get it sorted but dunno where to start when there's no error codes and the fact you have to take the car apart to get to things.
Sat typing this while in the car.. i know.. press the magic button to keep the heater going. Nope . Nothing.. nada
Sat typing this while in the car.. i know.. press the magic button to keep the heater going. Nope . Nothing.. nada
Last edited:
Datatek
Well-Known Member
- Posts
- 44,883
- Location
- Near Poitiers SW France
I'm not too bothered about looks, but easy enough to get wheels refinished and it doesn't cost a fortune or you could spray them yourself.
That was for Flossie who was talking about running a hosepipe over the car or driving at 140 to test for leaks. The rain in Spain goes mainly down the drain.
RangeRoller dt
Well-Sprung Member
- Posts
- 14,393
- Location
- Trapped inside my head @ LZ asylum
- Posts
- 33,599
- Location
- North Shropshire
They would probably look better than they did on the p38
- Posts
- 12,628
- Location
- Sud ouest France !
Unless your in Valencia
oddbob
Member
- Posts
- 94
- Location
- Middleton St. George
Today I 'ave mostly been sorting a Fuel Burning Heater remote for my 07 Rangey Roverer.
I started by following this idea, but without the wifi thing, which is where the trouble started, because I wasn't using what he used. The wiring was the same idea though, and I bought a cheap (less than a tenner off fleabay) remote relay. So it's a positive lead from the vehicle wiring to the + on the circuit board, with a connection to the 'com' terminal, earth to the - on the board, and a trigger wire from the 'no' connection to the vehicle loom.
At first it would only work if I kept my finger on the button, not ideal as that would lead to a sore finger and probably drain the remote battery in no time.
Then I found out that they need programming. There’s a small button on the circuit board, with 3 options; momentary (standard option – hence having to keep your finger on the button), toggle and latch. I used the latch option, one button on the remote for on, one for off.
This system is ideal for use at close range, if you need to operate the pre-heater whilst sat in an office then you’ll need a gsm system, and good look figuring that out. I used this video to suss it, now I need some nice bad weather to try it out for real.
I started by following this idea, but without the wifi thing, which is where the trouble started, because I wasn't using what he used. The wiring was the same idea though, and I bought a cheap (less than a tenner off fleabay) remote relay. So it's a positive lead from the vehicle wiring to the + on the circuit board, with a connection to the 'com' terminal, earth to the - on the board, and a trigger wire from the 'no' connection to the vehicle loom.
At first it would only work if I kept my finger on the button, not ideal as that would lead to a sore finger and probably drain the remote battery in no time.
Then I found out that they need programming. There’s a small button on the circuit board, with 3 options; momentary (standard option – hence having to keep your finger on the button), toggle and latch. I used the latch option, one button on the remote for on, one for off.
This system is ideal for use at close range, if you need to operate the pre-heater whilst sat in an office then you’ll need a gsm system, and good look figuring that out. I used this video to suss it, now I need some nice bad weather to try it out for real.
