Datatek
Well-Known Member
- Posts
- 44,883
- Location
- Near Poitiers SW France
The P38 weighs in a 2,25 tonnes, I wouldn't fancy using that for lifting my P38's. Mark has a scissor lift.
What did you do with your Range Rover today
- Thread starter Dopey
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Scotiawhiskers
Well-Known Member
- Posts
- 877
- Location
- Manchester
We don't intend to lift him completely, only one end at a time, so 2 wheels are still on the ground and taking load.
No such worry with the Ka.
Scotiawhiskers
Well-Known Member
- Posts
- 877
- Location
- Manchester
Lifted both ends separately no issues, was how we did the airbags.
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
Brake reservoir wouldn't hold pressure or fit.
I've been mulling this over. The liquid is likely to slosh around, left to right as you turn and front to rear as you brake / accelerate. Floats can be tempermental. The expansion tank is under pressure and the liquid gets pumped about, albeit ideally not through the expansion tank but who knows when coolant is low?!
A neighbours old VW has a low coolant alarm. It is built into the side of the reservoir and contains a high and low wire, a bit like the 2 screws trick. Now, I don't know what the difference in resistance between air and water / coolant mix is but I am guessing some sort of tuning is required? Either way, first thing is to have a play with a light / sounder, some wires and a battery in the garage and test the principle. After that I'll probably need a relay and maybe a potentiometer.
Moving on, it seems to me the head is the most important thing so bolting a sensor onto that seems like a good idea. That brings me back to the Engine Guard idea. In the end I'll probably end up doing both in some guise of another but I just need to have a think and a play first.
In the meantime the car did about 30 miles today and lost no visible coolant. I'm pretty sure it is losing only a little from where the coolant pipes go on the heater matrix tails. The clips I put on are the worm gear type and I think the heating / cooling cycle loosens them up. I am hoping (constant tension) clips like these with a spring might be an improvement:
Supra Constant Tension Clamp - 304SS - Dia=29-31mm
We have discounts and trade terms if you want to buy Supra Constant Tension Clamp - 304SS - Dia=29-31mm from HCL.
hcl-clamping.co.uk
Oetiker 178 Stepless Spring Clamp - 304SS - 26-32mm
StepLess® Screw Clamps are designed to provide a durable sealing for environments with strong thermal cycling. Self-tensioning StepLess® Screw Clamps are high performing clamps used in cooling systems. They are designed to withstand thermal cycling and increasing pressure – typical conditions in...
hcl-clamping.co.uk
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
One end on the ground and it'll have way less than 2 tons up in the air.
Datatek
Well-Known Member
- Posts
- 44,883
- Location
- Near Poitiers SW France
Two screws, when in the air due to coolant loss there will be an open circuit, when in the coolant there will be a circuit. One screw is placed such that it is always in the coolant and provides the source current, the other just below normal level. Something more sophisticated than a relay is normally used. There are lots of cheap electronic sensors that can be available.Brake reservoir wouldn't hold pressure or fit.
I've been mulling this over. The liquid is likely to slosh around, left to right as you turn and front to rear as you brake / accelerate. Floats can be tempermental. The expansion tank is under pressure and the liquid gets pumped about, albeit ideally not through the expansion tank but who knows when coolant is low?!
A neighbours old VW has a low coolant alarm. It is built into the side of the reservoir and contains a high and low wire, a bit like the 2 screws trick. Now, I don't know what the difference in resistance between air and water / coolant mix is but I am guessing some sort of tuning is required? Either way, first thing is to have a play with a light / sounder, some wires and a battery in the garage and test the principle. After that I'll probably need a relay and maybe a potentiometer.
Moving on, it seems to me the head is the most important thing so bolting a sensor onto that seems like a good idea. That brings me back to the Engine Guard idea. In the end I'll probably end up doing both in some guise of another but I just need to have a think and a play first.
In the meantime the car did about 30 miles today and lost no visible coolant. I'm pretty sure it is losing only a little from where the coolant pipes go on the heater matrix tails. The clips I put on are the worm gear type and I think the heating / cooling cycle loosens them up. I am hoping (constant tension) clips like these with a spring might be an improvement:
Supra Constant Tension Clamp - 304SS - Dia=29-31mm
We have discounts and trade terms if you want to buy Supra Constant Tension Clamp - 304SS - Dia=29-31mm from HCL.Oetiker 178 Stepless Spring Clamp - 304SS - 26-32mm
StepLess® Screw Clamps are designed to provide a durable sealing for environments with strong thermal cycling. Self-tensioning StepLess® Screw Clamps are high performing clamps used in cooling systems. They are designed to withstand thermal cycling and increasing pressure – typical conditions in...
It was about 8 quid off ebay.
I'll measure and model it before I fit and then I can have a go at printing one
- Posts
- 6,165
- Location
- North Manchester
I think the £8 one is more of a grey than white. Mine now has the grey one which seems to be holding up well.
- Posts
- 33,600
- Location
- North Shropshire
I got my engine from him. The only thing I'll say, at least in my case, he wasn't listing individual items.
Eg, the listing i looked at was an engine with 75000 miles on it. I got the first one off the shelf, l does he really have half a dozen engines all at the same mileage? Or does he grade them by how oily they look?
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
I got my engine from him. The only thing I'll say, at least in my case, he wasn't listing individual items.
Eg, the listing i looked at was an engine with 75000 miles on it. I got the first one off the shelf, l does he really have half a dozen engines all at the same mileage? Or does he grade them by how oily they look?
Dunno!
- Posts
- 33,600
- Location
- North Shropshire
Pretty sure the one i got had done way more than the 75k i bought, but you don't know until you strip it
That's the one I bought.
The one in the motor is so trashed there's no chance of copying it.
When I get this one I'll model it up in inventor and have a go at printing it.
I will have to get some abs or a better hotend for my printer as pla will not be strong enough and my hotend won't go hot enough for nylon.
Abs might work so ill try that first.
Attachments
- Posts
- 12,628
- Location
- Sud ouest France !
It's a scissor lift the one I have. 3t capacity.
http://www.jemaautolifte.fr/fr/products/JA3000S/146 not quite the same kiddo.
Datatek
Well-Known Member
- Posts
- 44,883
- Location
- Near Poitiers SW France
A car park fire at Bristol airport recently, not admitted the be a BEV though
Scotiawhiskers
Well-Known Member
- Posts
- 877
- Location
- Manchester
Electric CHT sensor like on aircraft, with a circuit that triggers a warning buzzer or light when it passes a threshold?Brake reservoir wouldn't hold pressure or fit.
I've been mulling this over. The liquid is likely to slosh around, left to right as you turn and front to rear as you brake / accelerate. Floats can be tempermental. The expansion tank is under pressure and the liquid gets pumped about, albeit ideally not through the expansion tank but who knows when coolant is low?!
A neighbours old VW has a low coolant alarm. It is built into the side of the reservoir and contains a high and low wire, a bit like the 2 screws trick. Now, I don't know what the difference in resistance between air and water / coolant mix is but I am guessing some sort of tuning is required? Either way, first thing is to have a play with a light / sounder, some wires and a battery in the garage and test the principle. After that I'll probably need a relay and maybe a potentiometer.
Moving on, it seems to me the head is the most important thing so bolting a sensor onto that seems like a good idea. That brings me back to the Engine Guard idea. In the end I'll probably end up doing both in some guise of another but I just need to have a think and a play first.
In the meantime the car did about 30 miles today and lost no visible coolant. I'm pretty sure it is losing only a little from where the coolant pipes go on the heater matrix tails. The clips I put on are the worm gear type and I think the heating / cooling cycle loosens them up. I am hoping (constant tension) clips like these with a spring might be an improvement:
Supra Constant Tension Clamp - 304SS - Dia=29-31mm
We have discounts and trade terms if you want to buy Supra Constant Tension Clamp - 304SS - Dia=29-31mm from HCL.Oetiker 178 Stepless Spring Clamp - 304SS - 26-32mm
StepLess® Screw Clamps are designed to provide a durable sealing for environments with strong thermal cycling. Self-tensioning StepLess® Screw Clamps are high performing clamps used in cooling systems. They are designed to withstand thermal cycling and increasing pressure – typical conditions in...
- Posts
- 4,653
- Location
- Rotherham
170 mile round trip to east coast to see the seals at Donna Nook today. 90 on motorway rest on main roads and back lanes. The P38 is a joy to drive, so smooth and comfy. It was a joy. 
RangeRoller dt
Well-Sprung Member
- Posts
- 14,393
- Location
- Trapped inside my head @ LZ asylum
Best to give him a ring to discuss your options. He is okay to deal with and knows his stuff. He’s got (used to have) so much stuff there is unbelievable. Knew Alan from way backI got my engine from him. The only thing I'll say, at least in my case, he wasn't listing individual items.
Eg, the listing i looked at was an engine with 75000 miles on it. I got the first one off the shelf, l does he really have half a dozen engines all at the same mileage? Or does he grade them by how oily they look?
stuu
Well-Known Member
- Posts
- 1,946
- Location
- Aberdeenshire
Trailer on, Picked up a Honda crv diesel that broke down with this ongoing issue happening when it feels like it,
And also bought a motd mk3 mondeo st tdci in the st blue off a pal for a 100,
He took subframe and engine and box out, put on a decent front subframe and new clutch and new springs and brakes and can't get it to start again it was a running driving motor i seen it drive into his unit,
Hopefully i can get it going and just use the rangie for work and the mondog to go to the unit and back most of the time save the rangie getting so dirty inside
And also bought a motd mk3 mondeo st tdci in the st blue off a pal for a 100,
He took subframe and engine and box out, put on a decent front subframe and new clutch and new springs and brakes and can't get it to start again it was a running driving motor i seen it drive into his unit,
Hopefully i can get it going and just use the rangie for work and the mondog to go to the unit and back most of the time save the rangie getting so dirty inside
D1Nut
Well-Known Member
- Posts
- 395
- Location
- South Africa
Grrrrrrr
on my D1 the brake reservoir has a level detector as part of the cap
after 25 years it still works so an off the shelf solution might exist
on my D1 the brake reservoir has a level detector as part of the cap
after 25 years it still works so an off the shelf solution might exist
