Datatek
Well-Known Member
- Posts
- 45,081
- Location
- Near Poitiers SW France
Dream onHoly Craaap, you should have mentioned it to them, they may have been horrified at the fact and done their best to put it right for you. (I'd like to think so)
What did you do with your Range Rover today
- Thread starter Dopey
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Datatek
Well-Known Member
- Posts
- 45,081
- Location
- Near Poitiers SW France
Nasty, and exactly why I never rely on garages.
doriz
Well-Known Member
- Posts
- 17,312
Cancelled the MOT until I can bottom out this SRS fault. History quite clean so pointless to add a fail at this point. Spent a few quid yesterday buying some bits and bobs, missing clips, over mats etc. more to follow. Gave it a wash at 8 am before it got warm, it always looks good a shiny after.
- Posts
- 12,673
- Location
- Sud ouest France !
Dream on
Hey, not all garages are bad, just most of them. I'd be horrified if a client of mine had to go through that because of a mistake I'd made.Nasty, and exactly why I never rely on garages.
- Posts
- 34,115
- Location
- North Shropshire
Have you checked the black box thingummy under the kick panel to the right of the steering column? Pretty sure i had to wiggle bits to make it work
Datatek
Well-Known Member
- Posts
- 45,081
- Location
- Near Poitiers SW France
I think you are one of a very rare breed. I knew one other like you, he had a back street repair shop specialising in Volvo's, he used get cars sent to him that the dealer couldn't fix. He used to put a bit of electronics/electrical work my wayHey, not all garages are bad, just most of them. I'd be horrified if a client of mine had to go through that because of a mistake I'd made.
- Posts
- 9,115
- Location
- North Lincs
That error has come back? I thought it was fixed
The nanocom couldn't see the error. I just wiggled the wires under the seats.
- Posts
- 12,673
- Location
- Sud ouest France !
Maybe the second bulb in the clocks has failed?That error has come back? I thought it was fixed
The nanocom couldn't see the error. I just wiggled the wires under the seats.
Well, that didn't go to plan. I thought whoever referb'd the FIP had replaced the antitamper bolt. They had not. I ordered the socket (I don't have any fasteners to replace it with so didn't want to drift on a regulat socket) and just cleaned up everything on and around the FIP so while I drive around until next weekend I can pin point where the leak is and try again. Lesson learnt, stop assuming things. Every job I've done over the last year or so required me postponing work while I buy the tool I need.
doriz
Well-Known Member
- Posts
- 17,312
Just fitted a new seat, a gleaming replacement. Let’s see what happens when I spark her up tomorrowThat error has come back? I thought it was fixed
The nanocom couldn't see the error. I just wiggled the wires under the seats.
doriz
Well-Known Member
- Posts
- 17,312
All bulbs replaced and checked. All connectors cleaned. Apparently the srs has a self check system and doesn’t log error codes. Hence why wiggling a wire can temp solve the issue.
RangeRoller dt
Well-Sprung Member
- Posts
- 14,416
- Location
- Trapped inside my head @ LZ asylum
stuu
Well-Known Member
- Posts
- 1,952
- Location
- Aberdeenshire
To be honest re the brake pipe, i did notice the wet rear arm and wheel i guess not far from it starting and it was pin hole still had a fairly decent pedal and thankfully able to keep a good distance and have a fully working handbrake incase
If the motor had been tested like it had most its life its been 6-7k miles between mots i dare say it would have been noticed sooner mabye, iv done 24k, its done more miles with me then it has in 4 years previously,
Iv done the rear break shoes and rear pads and changed all toe and camber bits and wheels was recently and iv never noticed myself either,
Maybe could drop by and mention it as a by the way or im not being a bugger but that was also 10months ago,
If the motor had been tested like it had most its life its been 6-7k miles between mots i dare say it would have been noticed sooner mabye, iv done 24k, its done more miles with me then it has in 4 years previously,
Iv done the rear break shoes and rear pads and changed all toe and camber bits and wheels was recently and iv never noticed myself either,
Maybe could drop by and mention it as a by the way or im not being a bugger but that was also 10months ago,
- Posts
- 12,673
- Location
- Sud ouest France !
Ahha, I thought it was just recently. Hopefully they wouldn't say it had shifted and rubbed against the arm, even though it shouldn't
Ah well, got the tool on the way now. Can add to the collection of tools I've assembled for jobs I won't be doing all that often. Always got it on hand if anyone else is in need.
- Posts
- 19,326
- Location
- Buckinghamshire, UK. ('95 DT)
Cupronickel better than copper.
Assume that is the same as kunifer? What I always used when I was a civvie VM. Bit harder to manipulate but would outlive the car.
Datatek
Well-Known Member
- Posts
- 45,081
- Location
- Near Poitiers SW France
