Datatek
Well-Known Member
- Posts
- 45,063
- Location
- Near Poitiers SW France
Lots of mice where i am in the middle of nowhere, the cats eat them for breakfast.
The dehumidifier will get the water out but it can take a long time.
What did you do with your Range Rover today
- Thread starter Dopey
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
The dehumidifier will get the water out but it can take a long time.
- Posts
- 12,669
- Location
- Sud ouest France !
Oh dear not good. I reckon the tc seal is weeping on mine as I’ve noticed a touch of dex 3 dripping from the bottom of the bell housing where it meets the engine. Might have a oil leak on the engine too done my best to clean up but can’t tell if old oil from when the rocker cover was leaking on @kermit_rr just getting heated up and dribbling down or wether it is indeed leaking again. Might also be leaking from the crankshaft/timing cover seal as there is a bit at the front that seems to be coming from roughly that area. Watched a video on replacing those seals the other night seems a bit involved but doesn’t seem like it’s a particular hard job for the timing case seals.Not a nice job... Fender puma transfer box seals leaking
The tc seal on the other hand I’ve got no way of getting the gearbox off so that will be a costly job for the sake of a few quid bit of rubber.
While I’m talking about gearbox a quick update after topping up the fluid the second time the previous weekend it’s running a lot smoother, used to get a good judder probably the wrong description as it wasn’t exactly a judder but it wasn’t what you would call a bang either right when it changed from 1st to 2nd now that is barely there really I only notice it because I knew it had it before otherwise if anyone drove it they wouldn’t know about it’s become that slight.
- Posts
- 6,243
- Location
- North Manchester
- Posts
- 34,073
- Location
- North Shropshire
I've got an impact socket, but how much stress do you put on a 1/2 inch breaker bar?
- Posts
- 6,243
- Location
- North Manchester
Till it breaks
Breaker bars are cheap for what they are so I wouldn’t worry too much, either that or get yourself a 3/4 inch bar that will get them off for sure.
- Posts
- 34,073
- Location
- North Shropshire
If i recall it wasn't a cheap one
Maybe i need a 22mm socket for my 3/4 breaker
In that case I’d order a socket for your 3/4 and probably a cheapo sacrificial 1/2 breaker bar aswell that way you can use both of needed and always handy to have one you don’t care about for this reason.
- Posts
- 19,317
- Location
- Buckinghamshire, UK. ('95 DT)
Worked a lot longer for Dopey than my stuff did.
Salisbury Nick
Well-Known Member
- Posts
- 790
- Location
- Dorchester
I like that your tool kit on the back wall is mostly hammers!Not a nice job... Fender puma transfer box seals leaking
Can't beat a bit of percussive maintenance
Last time I had swollen nuts I had to go hospital which made it worse, I couldn't sit for weeks it the left one was probably a good 10-13cm circumference
RangeRoller dt
Well-Sprung Member
- Posts
- 14,415
- Location
- Trapped inside my head @ LZ asylum
Diddle you think about orange?
- Posts
- 34,073
- Location
- North Shropshire
Last edited:
green is the new orange
- Posts
- 19,317
- Location
- Buckinghamshire, UK. ('95 DT)
That is the special Land Rover tool range. LRT-1-1 through to LRT-999-999. After that it is the grinder.
- Posts
- 34,073
- Location
- North Shropshire
Does that include the soft faced mallet to 'gently tap' the steering box from the chassis?
- Posts
- 34,073
- Location
- North Shropshire
its a 'does what is says on the tin' one, so i dont need to worry about breaking it!
wheelnuts sorted
RangeRoller dt
Well-Sprung Member
- Posts
- 14,415
- Location
- Trapped inside my head @ LZ asylum
green is the new orange
Theys is not ‘38 parts?
Hey who are you?
Where ya bin, hope all is good mate
I’m alive thats all I can promise
