What did you do with your Range Rover today

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
And talking about grounds......................Buttercup was starting to get a bit optional in the starting department, a few times I needed to turn the key 2 or 3 times to get the starter wizzing round. Everything seemed ok until I got to the ground off the starter to bulkhead, just a little loose so took off, still cleanish, but cleaned everything up and used some copper coat on re-assembly.
Seems to have fixed it, time will tell.:)
:)
 
Khemitude said:
Yeah that’s what I thought from looking at it, it was just stumping me as I was unsure where the tank stuff was coming out I should have asked you really but I found it anyway now.

I’m presuming the injector cut offs have already been done?
Click to expand...
Yes, i did label the lpg injector wires, so that should be straight forward. I hope. There's a lpg temp sensor and vacuum sensor as well
 
kermit_rr said:
Yes, i did label the lpg injector wires, so that should be straight forward. I hope. There's a lpg temp sensor and vacuum sensor as well
Click to expand...
Yeah I did already spot them as they were easy enough to figure out what with being proper connectors. Just need to plump in the gas line on the passenger side reducer as that was already hanging out, double check all the clamps are nice and tight and then do that last bit of wiring and with any luck, she will run. Turns out that are 3 places very local to me that sell the lpg gas and thats not including corley services which is also close by albeit more expensive being motorway though still cheaper than petrol. So should be pretty good for being able to use lpg most of the time I reckon at least for the forseeable future.
 
kermit_rr said:
Any ideas what i need to do to stop the reversing sensors from 'seeing' a trailer? Car recognises it's there, get the trailer icon on the dash when indicating.. it's easy to turn off with the button so not a big problem but would be nice if it worked properly
Click to expand...

Does the brain need telling there's a tow-bar fitted or have Land Rover done something clever to stol it recognising after-market kits? They'll be something for the tell-tale on the dash so can you take a feed off that to take the reversing sensor wire off the reverse switch either high or low?
 
kermit_rr said:
Ferfoooksake got bored of the beeps.. been meaning to check if i can get the wheel nuts off..
3foot breaker bar.. fail..
Guess that means the special tool in the boot won't work? :oops:
Click to expand...

Be careful. I've had 2 cars now where the nuts were on super tight and I wrecked the special tool trying to get the f*ckers off. One stud actually sheared off in the hub. Kids with windy-guns hammering them up!
 
Bix said:
Hey, new forum looks nice. I can finally share the pictures from when I changed the CV joint.
View attachment 286655

View attachment 286656

View attachment 286657

View attachment 286663

View attachment 286660

View attachment 286664

View attachment 286662

View attachment 286661

View attachment 286659

It was an absolute lickout. Was glad I was able to recruit a Fijian to crack off the hubnut. Was surprised to find the old joint was fine, the noise was all because a circlip failed. Not really sure what could've caused it to fail. But hey-ho, I had a full kit to replace the corner so I did anyway, means the old joint is now a spare. I just need a CV boot kit to keep in the garage just in case.

Also, the factory hub nut is 32mm, the replacement item was 36mm. Worth knowing in case you don't have a 36mm socket in the toolbox. I was lucky one of the wife's friend was able to pick one up for me from a popular orange store. Also, a 36mm socket only just fits in the centre bore of the wheel. Took a small amount of paint off the wheel when I tightened it up.
Click to expand...

That brings back horrible memories.

36mm is Britpart nut. There's a place in Brum that sells the 32 mm ones - much better because unless you have a 36mm thin walled socket the damn socket won't fit. Or you can get 32 mm off Land Rover if you need a cashectony. Trying to remember what the Brum site was called. Parts2u or something? Might be on my yhread where I did my CV boot.
 
Khemitude said:
Perfect this was just what I needed pictures and a bit of info as I’ve got a reluctor ring to replace which is essentially the same job either that or I just replace the cv joint anyway since that comes with a new ring though I’ve already got a ring that came with the car to replace it with. Though I don’t have a Fijian in my toolbox so that might be a bit difficult for me.

Edit: just had a look at the battery impact apparently it has 1625nm breakaway torque I would think that would be enough to undo it but who know.
Click to expand...

I did a How To in the Technical Section for doing the CV boot. Er, I wonder if that still exists on yhe new site?!
 
Grrrrrr said:
Be careful. I've had 2 cars now where the nuts were on super tight and I wrecked the special tool trying to get the f*ckers off. One stud actually sheared off in the hub. Kids with windy-guns hammering them up!
Click to expand...
You mean the locking nut? They are all well chewed up i might get a set of 25 new wheel nuts, who steals wheels anymore?
 
Grrrrrr said:
Does the brain need telling there's a tow-bar fitted or have Land Rover done something clever to stol it recognising after-market kits? They'll be something for the tell-tale on the dash so can you take a feed off that to take the reversing sensor wire off the reverse switch either high or low?
Click to expand...
I wouldn't have thought so as it appears to be factory fitted with a land rover instruction book.. but maybe bought from the main dealer at a later date? Maybe needs something switching in software
 
Got another 350ml out over night plus the 250ml I got out yesterday that I emptied before I left for the night.

Put a fan heater in mainly pointed at the folded over carpet sponge and Already got another couple hundred ml I reckon in the space of an 30 mins.


kermit_rr said:
I can't add up.. it's Sunday :p
Click to expand...
To be fair not a bad idea to have some spare lol.
 
Khemitude said:
Got another 350ml out over night plus the 250ml I got out yesterday that I emptied before I left for the night.

Put a fan heater in mainly pointed at the folded over carpet sponge and Already got another couple hundred ml I reckon in the space of an 30 mins.



To be fair not a bad idea to have some spare lol.
Click to expand...
One of the benefits of air.. it's not going to suck out that much, but it does help keep things dry
 
kermit_rr said:
One of the benefits of air.. it's not going to suck out that much, but it does help keep things dry
Click to expand...
Certainly, assuming I get onto the sealing up today presumably I won’t have to worry about mass amounts getting in soaking up the underside of the carpet.

Gotta do a favour for a mate first but that’s fine as it means I can borrow his car and grab some silicone and electricky stuff to finish sort out the lpg.

It’s a mini I will be driving so it’s gonna feel like my arse is on the floor and the suspension is so hard I’ll be lucky to have any discs not crushed to dust in my spine especially with the state of the roads round here
 
Khemitude said:
Certainly, assuming I get onto the sealing up today presumably I won’t have to worry about mass amounts getting in soaking up the underside of the carpet.

Gotta do a favour for a mate first but that’s fine as it means I can borrow his car and grab some silicone and electricky stuff to finish sort out the lpg.

It’s a mini I will be driving so it’s gonna feel like my arse is on the floor and the suspension is so hard I’ll be lucky to have any discs not crushed to dust in my spine especially with the state of the roads round here
Click to expand...
I resorted to installing disposable nappies under the carpet of our Jaguar to draw the moisture out of the foam on carpet underside to avoid having to pull them out, did the job. The water was getting in through a 5mm gap in the outer door rubber, what a pain.
Tricky :cool:
 
Tricky of York said:
It’s not the wheels any more it’s the tyres at £140 + per corner budget brand. If your wheels are half decent too I’d be fitting new locking nuts.
Tricky :cool:
Click to expand...
True enough, my wheels are shod in G015s. At almost £200 a corner now. 🙃
Although I was lucky that they were only £100 a corner when I got them. I could get a full set of 5 alloys for under £100.
 
Bix said:
True enough, my wheels are shod in G015s. At almost £200 a corner now. 🙃
Although I was lucky that they were only £100 a corner when I got them. I could get a full set of 5 alloys for under £100.
Click to expand...
I’m fortunate enough to have 20” for winter and 22” for summer so definitely locked, wouldn’t fancy having to replace those.
Tricky :cool:
 
Bix said:
True enough, my wheels are shod in G015s. At almost £200 a corner now. 🙃
Although I was lucky that they were only £100 a corner when I got them. I could get a full set of 5 alloys for under £100.
Click to expand...

Holy ****. My General Grabber AT2s were £100 a corner, fitted. Still plenty of tread on them so I will be running those until they're slicks.
 
You must log in or register to reply here.

Similar threads

A
Range Rover L322 - not turning over
Replies
12
Views
2K
gold rover
gold rover
B
L320 range rover sport 3.0 tdv6 loosing power steering fluid
Replies
3
Views
535
Mark Piercy
Mark Piercy
F
1980 Range Rover 2 door v8 to 300tdi
2
Replies
20
Views
1K
Grrrrrr
Grrrrrr
T
Non start
Replies
3
Views
717
Datatek
Datatek
T
Fan Clutch??
Replies
14
Views
799
Grrrrrr
Grrrrrr
Back
Top