What did you do with your Range Rover today
- Thread starter Dopey
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
Brake discs and pads replaced. However, looks like a caliper has had it so best replace those too.
While under there I discovered a front suspension damper had snapped! Oh, and a 4" hole in the exhaust at the rear. So, more help required from the plastic fantastic ...
While under there I discovered a front suspension damper had snapped! Oh, and a 4" hole in the exhaust at the rear. So, more help required from the plastic fantastic ...
stuu
Well-Known Member
- Posts
- 1,946
- Location
- Aberdeenshire
Had a play about the farm 
weimieman
Active Member
- Posts
- 246
- Location
- Just below the Lake District
Had a play about the farm
Nice .......
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
Didn't involve washing, I see.
Mind you, you should see the side of mine - still covered in mud from my frollick a few weeks ago.
Mind you, you should see the side of mine - still covered in mud from my frollick a few weeks ago.
Had a play about the farm
stuu
Well-Known Member
- Posts
- 1,946
- Location
- Aberdeenshire
It was washed last night but soon gets muddy again. Il give her a quick wash tomorrow night since il be up farm again tomorrow like to keep it clean during the week visiting customers homes always looks better in a clean motor you only get one 1st impression
zzr1200
Well-Known Member
- Posts
- 1,862
- Location
- Chesterfield, Derbyshire
Decided I couldn't be bothered to do my headlining, it now has a nice quilted effect with plastic studs holding it up at intervals. I use it as an example to others of Land Rover quality
Pictures, please...
raise:
Datatek
Well-Known Member
- Posts
- 44,886
- Location
- Near Poitiers SW France
Brave man
Littelwill
Well-Known Member
- Posts
- 3,065
- Location
- Lincolnshire
Out for a Sunday drive, drove past a "Road Closed" sign as it was same way back otherwise.
After a few miles a river had burst it's banks flooding the road for 3-400 yards.
A few cars on either side just sitting there, stopped and spoke with a van driver there needed through but didn't dare. (detour around 35 miles)
Rose the suspension and said he could watch me and decide, so I slowly drove through, glad the doors was closed, felt good,
the van driver and a waiting taxi decided to turn around.
Judging after passing the water level was just above the running boards as they had a clean.
Been on the road before and only half guessed it wasn't too deep
Great day out, sorry didn't bring camera
After a few miles a river had burst it's banks flooding the road for 3-400 yards.
A few cars on either side just sitting there, stopped and spoke with a van driver there needed through but didn't dare. (detour around 35 miles)
Rose the suspension and said he could watch me and decide, so I slowly drove through, glad the doors was closed, felt good,
the van driver and a waiting taxi decided to turn around.
Judging after passing the water level was just above the running boards as they had a clean.
Been on the road before and only half guessed it wasn't too deep
Great day out, sorry didn't bring camera
Castor
Trainee maniac
- Posts
- 680
- Location
- Ebley, Glos.
They're both black.
Nicktrackside
Active Member
- Posts
- 117
- Location
- Nuneaton Warwickshire.
Replaced the front wheel bearing and hub on my P38. Only took about 2 hours. I was putting the job off for ages, but MOT time so it had to be done.
biketeacherdave
Well-Known Member
- Posts
- 4,885
- Location
- south east london
great fun getting that axle nut off aint it
youngshag
Member
- Posts
- 50
- Location
- North Huyton, Liverpool
Got a 2nd hand anti roll bar off ebay, got it powder coated and changed the drop links and bushes. The bar came with poly bushes which looked very new so fitted them to try. Keeping the new oem rubber units just in case. All went on a doddle and only had to saw off one drop link.
Nicktrackside
Active Member
- Posts
- 117
- Location
- Nuneaton Warwickshire.
The axle nut was not a problem after i knocked the stake nut out of the groove in the axle. I am blessed with a body designed for jumping on the end of a long breaker bar.
the hardest part was removing the hub after I had unbolted it. I managed to loosen it by knocking it around until one bolt hole could be hammered from behind.
the hardest part was removing the hub after I had unbolted it. I managed to loosen it by knocking it around until one bolt hole could be hammered from behind.
tarphenry
Well-Known Member
- Posts
- 1,540
- Location
- bury lancs
Managed to buy a set of sidesteps for a ridiculously cheap price off fleabay ,picked them up today, in remarkably good condition. Very pleasantly surprised.
Littelwill
Well-Known Member
- Posts
- 3,065
- Location
- Lincolnshire
