what am i doing wrong

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Grrrrrr said:
Yes, I took the front liner out to make access easier. Only takes 5 minutes and then everything is just there.
Click to expand...
You are joking? The only way to get the liners off on mine would be to grind the heads off all the screws then remove the remains and fit new fastners, certainly not a 5 minute job:rolleyes:
 
Datatek said:
You are joking? The only way to get the liners off on mine would be to grind the heads off all the screws then remove the remains and fit new fastners, certainly not a 5 minute job:rolleyes:
Click to expand...

Unless you have mud flaps fitted, just five push in plastic rivets. Very easy to remove with the correct tool. Reusable :)
 
wammers said:
Unless you have mud flaps fitted, just five push in plastic rivets. Very easy to remove with the correct tool. Reusable :)
Click to expand...

Wammers is correct. Mine had little plastic rivets that were easy to extract and indeed reusable. Still on there now with no rattling.

Sounds like a previous owner didn't like plastic rivets?
 
G, yuo almost certainly can do it without removing the liner but it was my first time and I wanted to see what I was doing properly. Having done it I'll do it again because it made everything so easy!

Of course, if I had corroded steel bolts holding it in place I'd have been under the car in seconds!
 
so are we saying its easier with the liners out or in :confused: i would have thought by the time you mess on taking the liners out the clips would have been removed :p
 
The one clip I could not reach was accessed by drilling small hole in liner then pinging it off with screwdriver (V8)
ze8uhy5e.jpg
 
wammers said:
Unless you have mud flaps fitted, just five push in plastic rivets. Very easy to remove with the correct tool. Reusable :)
Click to expand...
Don't they all have mud flaps fitted? There is one plastic fastner and 3 or 4 rusted screws, they can't even be ground off easily as they are recessed into the mudflap. I gave up and found the liner was easily levered out enough to access the clips.:)
 
Datatek said:
Don't they all have mud flaps fitted? There is one plastic fastner and 3 or 4 rusted screws, they can't even be ground off easily as they are recessed into the mudflap. I gave up and found the liner was easily levered out enough to access the clips.:)
Click to expand...

Maybe a good idea to spend a day replacing mud flap fasteners and waxing them up. They screw into plastic retainers so with the head off should be easy to remove with grips. One job for me to do this summer. Should be around five plastic rivets holding liner on. Easy to remove with correct tool and can be reused. These http://www.rimmerbros.co.uk/Item--i-ANR2224
 
Last edited:
wammers said:
Maybe a good idea to spend a day replacing mud flap fasteners and waxing them up. They screw into plastic retainers so with the head off should be easy to remove with grips. One job for me to do this summer. Should be around five plastic rivets holding liner on. Easy to remove with correct tool and can be reused. These Plastic Rivet - Genuine Land Rover at www.rimmerbros.co.uk
Click to expand...
I'll wait for the feckers to rust off then replace them, not going to waste my time on it.
 
You must log in or register to reply here.

Similar threads

B
EAS one corner down
Replies
6
Views
245
BigJessie
B
B
P38A 1996 4.6 Auto HSE. driver side bags not inflating after valve block rebuild.
Replies
17
Views
1K
nigelbb
N
M
HELP PLEASE. Rear Loading bay window
Replies
7
Views
442
mudinuri
M
C
Suspension issues, driving me mad
Replies
1
Views
560
Graculus
Graculus
seldom
L320 rear bushes
Replies
8
Views
416
Mark Piercy
Mark Piercy
Back
Top