Turbo cartridge

Dseasy · Oct 31, 2022

I was wondering if i could call on some collective wisdom, i need a new turbo cartridge for my old p38 dse 2001, dont ask what happened, of course its a td04 11g-4 but my question is will any td04 11g-4 cartridge work? And what is the significance of the other numbers?
Dse's are pretty uncommon here so parts are hard to get. I still have the old turbo so i just wanted to chuck a new cartridge in the turbo housing. Can anyone clarify for me so i can stick the old girl back together

Quixote · Nov 1, 2022

OK; the suspense is killing me! WTF is a turbo cartridge?

Datatek · Nov 1, 2022

Quixote said:
OK; the suspense is killing me! WTF is a turbo cartridge?

Replacement innards for a turbo charger

brianp38dse · Nov 1, 2022

From what i found out look at replacing mine was that the CHRA which is what they call the middle bit is the same for quite a few motors, they even do one on Alliexpress.

Quixote · Nov 1, 2022

Datatek said:
Replacement innards for a turbo charger

Let's face it: I'm simply not keeping up with this modern World.

Grrrrrr · Nov 1, 2022

Dseasy said:
I was wondering if i could call on some collective wisdom, i need a new turbo cartridge for my old p38 dse 2001, dont ask what happened, of course its a td04 11g-4 but my question is will any td04 11g-4 cartridge work? And what is the significance of the other numbers?
Dse's are pretty uncommon here so parts are hard to get. I still have the old turbo so i just wanted to chuck a new cartridge in the turbo housing. Can anyone clarify for me so i can stick the old girl back together View attachment 277332

Someone did this recently. Might have been @Slooby ?

Slooby · Nov 1, 2022

I didn't buy a new CHRA for mine, but did rebuild it with an after market seal and bearing kit (which was about £25 here in the UK) because the shaft, exhaust compressor and exhaust wheels were fine...right up until I tried to torque the new left hand thread 12 point lock nut down at 8Nm and discovered that my 1/4 drive Teng torque wrench didn't actualy have a torque function when switched to left handed tightening

I ended up buying a Mellet branded new shaft complete with exhaust wheel which was about £40 and was a lot more careful about tightening the lock nut...

As the Mitsubishi TD series turbos are sleeve bearing types they are pretty robust and basic so a DIY rebuild of the CHRA is perfectly acheivable, asuming your exhaust wheel, shaft and compressor wheel are undamaged or aren't worn.

I'll dig into my project thread to find my turbo rebuild sections as I photographed everything, and also detailed which version of bearing was used by BMW when they manufactured the turbo under licence from Mitsubishi.

Slooby · Nov 1, 2022

Rebuild kit was a Flat Back Rebuild Kit bought from
https://www.turborebuild.co.uk/webs...urbocharger-Bearings-and-Seals-Flat-Back.html

I gave them a call to make sure it was the right rebuild kit and ordered it along with the gaskets (which I can't actually find on their site) and Royal Mail 1st Class shipping which all came to 25 quid and some pennies inc VAT

And rebuilding it looked like this:

Gunge central...

Slooby · Nov 1, 2022

New (Melett) exhaust wheel and shaft turned up last week and I set about the second, partial, rebuild (partial because I only needed to refit the shaft and wheels).

First off here's a line up all the CHRA parts from the first full rebuild:

And now the assembled CHRA with new shaft and exhaust wheel:

The turbo is now all back together:

Had a fair old battle with getting the compressor housing circlip back on as I didn't have a big enough set of circlip pliers, also the all-metal lock nut on the exhaust housing to CHRA V band for some reason seized and snaped about 3mm off the end of the bolt, and the exhaust housing to CHRA joint didn't go back together as tightly as I expected. After a few attempts to get it close up I measured things up with my vernier and it would appear there was no way it could close up tight anyway, so fingers crossed it's all ok.

Dseasy · Nov 8, 2022

Slooby said:
I didn't buy a new CHRA for mine, but did rebuild it with an after market seal and bearing kit (which was about £25 here in the UK) because the shaft, exhaust compressor and exhaust wheels were fine...right up until I tried to torque the new left hand thread 12 point lock nut down at 8Nm and discovered that my 1/4 drive Teng torque wrench didn't actualy have a torque function when switched to left handed tightening

I ended up buying a Mellet branded new shaft complete with exhaust wheel which was about £40 and was a lot more careful about tightening the lock nut...

As the Mitsubishi TD series turbos are sleeve bearing types they are pretty robust and basic so a DIY rebuild of the CHRA is perfectly acheivable, asuming your exhaust wheel, shaft and compressor wheel are undamaged or aren't worn.

I'll dig into my project thread to find my turbo rebuild sections as I photographed everything, and also detailed which version of bearing was used by BMW when they manufactured the turbo under licence from Mitsubishi.

thanks guy but the shaft is broken so no rebuild for me although i have a rebuild kit

Grrrrrr · Nov 8, 2022

Dseasy said:
thanks guy but the shaft is broken so no rebuild for me although i have a rebuild kit

Shafted!

Rubberknees · Nov 8, 2022

Grrrrrr said:
Shafted!

Oooh nowt like a good bit of shafting

Slooby · Nov 9, 2022

Dseasy said:
thanks guy but the shaft is broken so no rebuild for me although i have a rebuild kit

Was the compressor wheel damaged, or can you, just like I did, get away with buying a new exhaust wheel and shaft for a lot less than a complete CHRA?

Turbo cartridge

Dseasy

New Member

Quixote

Member

Datatek

Well-Known Member

brianp38dse

Well-Known Member

Quixote

Member

Grrrrrr

Technician, Bodgit & Scarper Ltd

Slooby

Well-Known Member

Slooby

Well-Known Member

Slooby

Well-Known Member

Dseasy

New Member

Grrrrrr

Technician, Bodgit & Scarper Ltd

Rubberknees

Well-Known Member

Slooby

Well-Known Member

Similar threads