KISSMYAURA
Well-Known Member
- Posts
- 2,799
- Location
- KENT
Just need to mask up and dust so screws get a dose of raptor etc, next Optimil hinges and new NSF door.
TD5 90 Project
- Thread starter KISSMYAURA
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Stone56
Well-Known Member
- Posts
- 3,176
- Location
- Up a mountain
You got the same problem as me mud all up the side are them wheel spats sill available that fit at the bottom of arch ?
KISSMYAURA
Well-Known Member
- Posts
- 2,799
- Location
- KENT
not sure, have not seen any i like not too fussed about the mud to be honest, more interested in the Gwyn Lewis thing that stops stuff going over yer chassis legs for the front inner arch etc
KISSMYAURA
Well-Known Member
- Posts
- 2,799
- Location
- KENT
Next up!
Rear discs ( wavey daveys )
Rear Pads EBC Green
OSR caliper
And poxy turbo wastegate keeps sticking so will have to sort that as well.
Rear discs ( wavey daveys )
Rear Pads EBC Green
OSR caliper
And poxy turbo wastegate keeps sticking so will have to sort that as well.
KISSMYAURA
Well-Known Member
- Posts
- 2,799
- Location
- KENT
Spare wheel cover refresh.
KISSMYAURA
Well-Known Member
- Posts
- 2,799
- Location
- KENT
Custom Remap tomorrow, looking fwd to it, but not to the the early start lol
Already got:
Decat straight pipe,EGR del,high flow filter,Silicone hoses.
Cant stretch to an intercooler just yet.
Thanks to Harry@UKDEFENDERS
Ended up with a tweaked stage 2 no smoke
its mental! hits 2000 revs turbo kicks in with extra boost and goes like a two stoke up to 4500 waaaaaaaaaaaaaaaa, .... errr.....waaaaaaaaaaaaaaa
Already got:
Decat straight pipe,EGR del,high flow filter,Silicone hoses.
Cant stretch to an intercooler just yet.
Thanks to Harry@UKDEFENDERS
Ended up with a tweaked stage 2 no smoke
its mental! hits 2000 revs turbo kicks in with extra boost and goes like a two stoke up to 4500 waaaaaaaaaaaaaaaa, .... errr.....waaaaaaaaaaaaaaa
Last edited:
KISSMYAURA
Well-Known Member
- Posts
- 2,799
- Location
- KENT
NSR Cally-purrr and new rear discs, bearings etc all ordered up for the bank holiday.
And while im there pioneer braided brake lines and caliper hard lines
And while im there pioneer braided brake lines and caliper hard lines
Last edited:
KISSMYAURA
Well-Known Member
- Posts
- 2,799
- Location
- KENT
Easter Bunny has delivered some toys for me:
Hicap phill
Well-Known Member
- Posts
- 16,181
- Location
- Wiltshire
Are the brake pads like the picture on the box??
If they are you want anti chatter springs,them black clips are for the early pads with single nipple in the middle.
Looks good though. Have you also got some brake pipe,you know what’s going to happen when you try to remove from the rear caliper
Anaconda
Well-Known Member
- Posts
- 3,463
- Location
- Thames Valley
Think the 90 had them clips on the rear
bankz5152
Well-Known Member
- Posts
- 9,300
- Location
- South London/North Kent
Busy boy! Need to do my rear calipers and discs at some point soon but not very soon 
KISSMYAURA
Well-Known Member
- Posts
- 2,799
- Location
- KENT
generic pic, actuals are in light blue on the box end with middle nip...
Rear hard lines i did with kunifer a year ago so should be good, but i got plenty of pipe n fittings etc.
Some of the stuff I ordered is also for stock shelf, prefer to have stuff on shelf for rainy days etc.
KISSMYAURA
Well-Known Member
- Posts
- 2,799
- Location
- KENT
Oil n oil filters service today.
Dry as a bone underneath now i got the transfer box o ring sorted, most unlike a fender......
Dry as a bone underneath now i got the transfer box o ring sorted, most unlike a fender......
bankz5152
Well-Known Member
- Posts
- 9,300
- Location
- South London/North Kent
Nice! Mines a little damp. Weep from the rear diff but wont be bothering as itll be changed soon enough.
TX box has a slight weep on the output shaft, I will get to that one!
TX box has a slight weep on the output shaft, I will get to that one!
KISSMYAURA
Well-Known Member
- Posts
- 2,799
- Location
- KENT
ha! im sure myne wont stay like that for long, like the leaks its a game of wits lol
KISSMYAURA
Well-Known Member
- Posts
- 2,799
- Location
- KENT
So in 2019 swapped it out for DAYCO, checked my belt today..... not a single crack looks as new as the day it was fitted.
KISSMYAURA
Well-Known Member
- Posts
- 2,799
- Location
- KENT
A few makes that in my opinion are the best quality you can get:
DAYCO or GATES for belts, tensioners, pulleys
LEMFORDER for balljoints A Frame and other suspension parts
TIMKEN bearings and races
SUPAPRO Bushes
OLD MAN EMU Shocks and Springs
PIONEER Brake Hoses
LOF Clutchs SMF Flywheels, Clutch master and slave cylinders
GKN Universal Joints
DAYCO or GATES for belts, tensioners, pulleys
LEMFORDER for balljoints A Frame and other suspension parts
TIMKEN bearings and races
SUPAPRO Bushes
OLD MAN EMU Shocks and Springs
PIONEER Brake Hoses
LOF Clutchs SMF Flywheels, Clutch master and slave cylinders
GKN Universal Joints
KISSMYAURA
Well-Known Member
- Posts
- 2,799
- Location
- KENT
A few makes that in my opinion are the best quality you can get:
DAYCO or GATES for belts, tensioners, pulleys
LEMFORDER for balljoints A Frame and other suspension parts
TIMKEN bearings and races
SUPAPRO Bushes
OLD MAN EMU Shocks and Springs
PIONEER Brake Hoses
LOF Clutchs SMF Flywheels, Clutch master and slave cylinders
GKN Universal Joints
KISSMYAURA
Well-Known Member
- Posts
- 2,799
- Location
- KENT
Just took delivery of my stainless repeater guards from "Bankzworx" 
Superb!
Superb!
Last edited:
bankz5152
Well-Known Member
- Posts
- 9,300
- Location
- South London/North Kent
Yeaaah glad they arrived!
Id use countersunk rivnuts on the sides gives a nicer flatter fit!
Id use countersunk rivnuts on the sides gives a nicer flatter fit!
